Browsing Publikasjoner fra CRIStin - NTNU by Title
Now showing items 8216-8235 of 37304
-
Design of a cold thermal energy storage unit for industrial applications using CO2 as refrigerant
(Chapter, 2019)Natural refrigerants such as ammonia, hydrocarbons and CO2 are becoming increasingly popular due to favorable thermo-physical properties, low environmental impact and low cost. Industrial refrigeration systems are often ... -
Design of a compact, reconfigurable, prosthetic wrist
(Journal article; Peer reviewed, 2012)The design of a prosthetic wrist is the result of compromises between the function and the practicality of the device. Conventional prosthetic wrists use a single degree of freedom to produce pro/supination of the hand. ... -
Design of a medical decision-supporting system for the identification of brain tumors using entropy-based thresholding and non-local texture features
(Journal article; Peer reviewed, 2023)Introduction: Brain tumors arise due to abnormal growth of cells at any brain location with uneven boundaries and shapes. Usually, they proliferate rapidly, and their size increases by approximately 1.4% a day, resulting ... -
Design of a monitoring system for a long-span suspension bridge: optimal sensor placement
(Chapter, 2020)The design of systems for structural health monitoring is an exercise that requires careful planning of optimal sensor locations. The number of possible locations usually outnumbers the number of available sensors, which ... -
Design of a nonlinear damping control scheme for nanopositioning
(Journal article; Peer reviewed, 2013)The application of a nonlinear control law for vibration damping on a typical nanopositioning system is investigated. The nonlinear control law is an augmentation of the linear integral force feedback scheme, where the ... -
Design of a novel hybrid process for membrane assisted clean hydrogen production with CO2 capture through liquefaction
(Peer reviewed; Journal article, 2022)This work introduces a novel hybrid concept to produce H2 from natural gas by using the protonic membrane reformer (PMR) with liquefaction based CO2 capture system. For process intensification, recycling of the off-gas ... -
Design of a Power-Dense Aviation Motor With a Low-Loss Superconducting Slotted Armature
(Peer reviewed; Journal article, 2023)This article describes the design and analysis of a 2.5-MW, 5000-rpm electric motor with a slotted armature employing REBCO high-temperature superconductors (HTS). The alternating current and field in the armature induces ... -
Design of a practical and compact mm-wave MIMO system with optimized capacity and phased arrays
(Journal article; Peer reviewed, 2014)In this paper we evaluate the feasibility of short range outdoor mm-wave MIMO links in the 70 GHz portion of the E-band (71–76 GHz). We use phased arrays in order to strongly reduce the impact of the multipath components, ... -
Design of a Social Innovation Competence Framework to Educate Entrepreneurs in Developing on the International Stage
(Chapter, 2022)The European Commission identifies entrepreneurship as one of eight competences necessary for all members of a knowledge-based society. The Entrepreneurship Competence Framework (EntreComp framework) is a tool that European ... -
Design of a study evaluating the effects, health economics, and stakeholder perspectives of a multi-component occupational rehabilitation program with an added workplace intervention - A study protocol
(Journal article; Peer reviewed, 2018)Background Recent research has suggested that interventions at the workplace might be the most potent ingredient in return to work interventions, but few studies have investigated the different effects of workplace ... -
Design of a sustainable maritime multi-modal distribution network – case study from automotive logistics
(Peer reviewed; Journal article, 2020)Multi-modal transportation takes advantage of multiple transport modes and can be an effective way to ease the negative environmental effects of freight transportation. This paper addresses a multi-modal distribution network ... -
Design of an Experimental ORC Expander Setup Using Natural Working Fluids
(Chapter, 2019)Organic Rankine Cycles (ORC) are an efficient and cost-effective technology to generate power from waste heat. Arguably, the two most important factors affecting the performance of the Rankine cycle are the choice of working ... -
Design of Bimetallic PtFe-Based Reduced Graphene Oxide as Efficient Catalyst for Oxidation Reduction Reaction
(Peer reviewed; Journal article, 2022)Oxygen reduction reaction (ORR) is a very important reaction that occurs at the cathodic side in proton exchange membrane fuel cells (PEMFCs). The high cost associated with frequently used Pt-based electrocatalysts for ORR ... -
Design of Digital Planner and 3D Vision System for Robot Bin Picking
(Chapter, 2023)Robot bin picking plays an important role in modern manufacturing process. In order to make these manufacturing systems more efficient and productive, it is essential to make a valid grasping plan from gripper design, ... -
Design of digital technologies for children
(Chapter, 2021)This chapter focuses on children aged around 5-11 insofar as this is the population most able to extract value from digital content while also being intrinsically different from older children in terms of their design ... -
Design of Dual Purpose No-Voltage Combined Windings for Bearingless Motors
(Journal article; Peer reviewed, 2017)A winding design approach is proposed to create a single motor winding, which is able to produce both radial force and torque. This approach can be used to design new bearingless motors, as well as to transform conventional ... -
Design of Experiment as a powerful tool when applying Finite Element Method: a case study on prediction of hot rolling process parameters
(Journal article; Peer reviewed, 2018)The ultimate goal in hot roll pass design is to manufacture a rolled product with the required dimensional accuracy, defect free surface, and mechanical properties. The proper selection of process parameters is crucial to ... -
Design of experiment for sports equipment - experimentally mapping the design space for paralympic alpine outriggers
(Journal article, 2021)This article presents a design of an experiment for investigating the effect of changing the geometry of Paralympic alpine sit-ski poles/outriggers in the LW 10-12 class. An experiment design for mapping an individual ... -
Design of four-band multispectral imaging system with one single-sensor
(Journal article; Peer reviewed, 2018)In order to acquire multispectral images precisely and quickly, a four-band multispectral capturing system with one imaging sensor is designed and evaluated in this paper. Firstly, four imaging bands are arranged in a 22 ...