Blar i Institutt for maskinteknikk og produksjon på tittel
Viser treff 239-258 av 3979
-
Analyse av utmattingspåkjente komponenter til stirlingmotor
(Master thesis, 2013)Denne masteroppgaven har sett på gjengeforbindelsene i stempelstangen i Single-Phase Powers stirlingmotor. Det har blitt gjort beregninger og analyser for å finne årsaken til to brudd som har forekommet i stempelstangen. ... -
Analyse av utmattingspåkjente komponenter til Stirlingmotor
(Master thesis, 2013)Denne masteroppgaven beskriver vurdering med fokus på utmatting av krysshode og stempelstang i en Stirling varmepumpe. Komponentene er utsatt for et stort antall vekslende belastninger i tillegg til kraftig forspenning. ... -
Analyse av vannforbuk i Kizilirmak ved bruk av WEAP- modellen: Effekter av klimaendringer og økt vannuttak
(Master thesis, 2014)I 2009 kjøpte Statkraft en portefølje med tre tyrkiske vannkraftprosjekt; Cakit (20 MW), Kargi (102 MW) og Cetin (517 MW) i tre separate vassdrag. Med disse tre kraftverkene vil Statkraft i 2015 ha en gjennomsnittlig ... -
Analyse av VVS-installasjoner og tilhørende drift- og vedlikeholdsplaner i idrettshall.
(Bachelor thesis, 2020)Idrettshaller har større ventilasjonsbehov enn andre konvensjonelle byggverk som kontorer og boliger. Med økt aktivitetsnivå avgir personer mer varme, og ventilasjonsbehovet øker. Da er det viktig med gode løsninger for ... -
Analyse og feilsøking av oppvarmingsanlegget til en privat enebolig
(Bachelor thesis, 2021)En enebolig har et varmeanlegg som ikke fungerer ifølge huseier. Det har derfor blitt utarbeidet en årsakrapport og kommet med eventuelle forbedringsforslag. Dette er gjort ved hjelp av en kartleggingsprosess av varmeanlegget ... -
Analyse og redesign av gir og girhus for elektromotor
(Master thesis, 2015)I denne oppgaven er en elektromotor utviklet av Adigo AS blitt studert, og elektromotorens gir har blitt analysert med formål å lage et skreddersydd gir og en redesignet elektromotor. Teori rundt tannhjul, tannhjulstransmisjoner ... -
Analysing environmental impacts from waste, water and wastewater infrastructure in the early phase planning of new urban settlements
(Doktoravhandlinger ved NTNU, 1503-8181; 2013:120, Doctoral thesis, 2013)Reducing the level of greenhouse gas emissions is on the policy agenda in many countries, including Norway. Human settlements draw on resources and cause emissions in many different ways, for example through direct energy ... -
Analysing the Main Standards for Climate-Induced Mechanical Risk in Heritage Wooden Structures: The Case of the Ringebu and Heddal Stave Churches (Norway)
(Peer reviewed; Journal article, 2022)Studying, controlling and extrapolating the indoor microclimate of historical buildings have always been at the forefront among numerous preventive conservation strategies, especially in case of buildings made of organic ... -
“Analysis and Improvement of Internal Logistics in the Library Sector through Autonomous Mobile Robots: A Case Study of Trondheim Public Library”
(Master thesis, 2024)Denne avhandlingen er resultatet av et samarbeid mellom NTNUs Institutt for maskin- og industriell teknologi og Trondheim folkebibliotek (TPL). Den er en del av det flerårige prosjektet SmartLIB, som fokuserer på utviklingen ... -
Analysis and modelling of recent large floods on the river Gaula
(Master thesis, 2015)In order to study the flood from 2009, 2010 and 2011 that have been impacting the Gaula waterway, a hydrological and operational model have been built. A brief description of the study is given as an introduction, followed ... -
Analysis and optimisation of books flow among branches through simulation: the case of Trondheim’s Public Library
(Master thesis, 2022)Denne oppgaven omhandler analyse og optimalisering av strømmene av bøker som genereres mellom de ulike stedene til Trondheim folkebibliotek, Trondheim folkebibliotek, som ligger i Trondheim, en by i Nord-Norge. ... -
Analysis of a Novel Wedge-Burst Test Design with Integrated Load Cells: A Comparison to the Split-Disk Test and an Investigation of the Effects of an Elastomeric Distributor
(Master thesis, 2020)En wedge-burst (kile-burst) test med integrerte lastceller har blitt sammenlignet med en split-disk test ved hjelp av finite element analyser (FEA). Oppførselen til sylinderspenningen og den kalkulert spenning for begge ... -
Analysis of a Pre-Tensioning Concept for a Floating Bridge Support Structure
(Master thesis, 2015)This thesis regards a pretensioning procedure for a large and slender support structure planned built below a floating bridge. First and foremost, global aspects are discussed with little consideration for local phenomenons. ... -
Analysis of Aluminium Hot Forging
(Doktoravhandlinger ved NTNU, 1503-8181; 2005:3, Doctoral thesis, 2005) -
Analysis of camshaft gear transmission for a ship engine
(Master thesis, 2015)This thesis investigates the dynamic behavior of a spur gear pair. The gears studied are somewhat similar to the ones found in Bergen Engines medium-speed diesel engine with regards to design, but some assumptions have ... -
Analysis of Challenges associated with Implementing Agile Project Management
(Master thesis, 2011)The purpose of this study was to investigate and analyze challenges associated with contracting, subcontracting, estimation process, risk management and success measurement. Qualitative method was applied in this study. ... -
An Analysis of CII's 10-10 Performance Assessment Program in Statnett
(Master thesis, 2017)The Constructions Industry Institute has developed a system known as the 10-10 Performance Assessment Program to meet the growing demands for a comprehensive performance measurement system in the construction sector that ... -
Analysis of Compact Separation Systems and Experimental Study of Centrifugal Separation in Helically Coiled Pipes
(Master thesis, 2015)The offshore petroleum industry is experiencing challenges as exploration and production are forced towards remote and deep reservoirs, combined with high cost-efficiency demands. Topside facilities struggle with limited ... -
Analysis of domino scenarios in chemical and process facilities operating in harsh environmental conditions
(Chapter, 2018)In the framework of chemical and process industry, accidental fires may lead to damages to equipment with severe consequences and possible domino effects. The availability and effectiveness of safety measures, aimed at ... -
Analysis of ESAFORM 2021 cup drawing benchmark of an Al alloy, critical factors for accuracy and efficiency of FE simulations
(Peer reviewed; Journal article, 2022)This article details the ESAFORM Benchmark 2021. The deep drawing cup of a 1 mm thick, AA 6016-T4 sheet with a strong cube texture was simulated by 11 teams relying on phenomenological or crystal plasticity approaches, ...