Blar i Fakultet for ingeniørvitenskap (IV) på tittel
Viser treff 401-420 av 23135
-
A new approach to the identification of high-potential materials for cost-efficient membrane-based post-combustion CO2 capture
(Journal article; Peer reviewed, 2018)Developing “good” membrane modules and materials is a key step towards reducing the cost of membrane-based CO2 capture. While this is traditionally being done through incremental development of existing and new materials, ... -
A new combination of conditional environmental distributions
(Journal article, 2018)In this paper, a joint distribution of all relevant environmental parameters used in design of offshore structures including directional components is presented, along with a novel procedure for dependency modelling between ... -
A New Concept of Multi-Scenario, Multi-Component Animated Maps for the Visualization of Spatio-Temporal Landscape Evolution
(Journal article; Peer reviewed, 2011)In this paper, we propose a new approach to the presentation of the spatio-temporal evolution of landscape using a multi-component multi-scenario animated map system. The concept of multi-scenario map was introduced with ... -
A new design concept of Blowout Preventer for decision support
(Chapter, 2017)The Blowout Preventer (BOP) system is used for controlling blowout risks in drilling operations. The system is implemented to shut down an oil and gas well when the well fluids have entered the wellbore. All BOP systems ... -
A new design for Elgeseter Street with focus on improving social aspects and walkability
(Master thesis, 2023)Den urbane utviklingen i Trondheim har satt i gang prosessen rundt oppgradering av byens hovedveier, der en av dem er Elgeseter Gate. Elgeseter-området er svært befolket ettersom mange har bosatt seg i området, i tillegg ... -
A new Design of a Francis Turbine in order to reduce Sediment Erosion
(Master thesis, 2010)This Master Thesis is about the sand erosion challenges with the Francis turbines. The background for studying this subject is the fact that the sand erosion problem is a very negative factor for the development of new ... -
A new dynamic void Growth Model
(Doktoravhandlinger ved NTNU, 1503-8181; 2004:118, Doctoral thesis, 2004)This work develops a new void growth model which is capable of describing the deformation and fracture of ductile materials under dynamic loading conditions. A representative volume element (RVE) which consists of a ... -
A New Extended Corresponding States Equation of State for Modelling CO2-Water Thermodynamics - A Compromise for CFD
(Doctoral theses at NTNU;2017:264, Doctoral thesis, 2017)This PhD work is part of the CO2 Dynamics project in collaboration with Sintef Energy. We investigated the importance of accurate modelling of CO2 thermodynamic properties for process design. The study was conducted for ... -
A New Foundation Model for Integrated Analyses of Monopile-based Offshore Wind Turbines
(Journal article; Peer reviewed, 2017)Offshore wind turbines are highly dynamic and tightly coupled systems subjected to variable cyclic loads. Designing and optimizing the support structure is a complex task, where several load scenarios have to be analysed ... -
A new laboratory apparatus for the measurement of seismic dispersion under deviatoric stress conditions
(Journal article; Peer reviewed, 2016)A better understanding of seismic dispersion and attenuation of acoustic waves in rocks is important for quantitative interpretation of seismic data, as well as for relating seismic data, sonic-log data, and ultrasonic ... -
A New Level Set Numerical Wave Tank with Improved Density Interpolation for Complex Wave Hydrodynamics
(Journal article; Peer reviewed, 2016)A new three-dimensional numerical wave tank is developed for the calculation of wave propagation and wave hydrodynamics by solving the incompressible Navier–Stokes equations. The free surface is modeled with the level set ... -
A new look toward relational project delivery models
(Doctoral theses at NTNU;2018:372, Doctoral thesis, 2018) -
A new method for assessing anisotropy in fused deposition modeled parts using computed tomography data
(Journal article; Peer reviewed, 2019)Voids in fused deposition modeled (FDM) parts are assumed to be a key driver for their anisotropic behavior. However, these assumptions are based on investigations of voids using only 2D data (microscopy images). This paper ... -
A New Method for Measuring the Ice Adhesion Strength of Anti-Icing Coatings
(Master thesis, 2014)This work provides a new method for measuring the ice adhesion strength of anti-icing coatings. An extensive literature review was performed to investigate the different means by which other researchers have performed ice ... -
A new method for underwater archaeological surveying using sensors and unmanned platforms
(Journal article; Peer reviewed, 2016)As most of the world’s oceans are inaccessible to diving archaeologists, we must rely on advanced underwater technology and marine robotics to explore, map and investigate ship wrecks in these areas. New sensors and unmanned ... -
A New Method of Low Amplitude Signal Detection and Its Application in Acoustic Emission
(Journal article; Peer reviewed, 2020)A novel methodology is proposed to enhance the reliability of detection of low amplitude transients in a noisy time series. Such time series often arise in a wide range of practical situations where different sensors are ... -
A new method to estimate the residual stresses in additive manufacturing characterized by point heat source
(Journal article; Peer reviewed, 2019)Residual stress in additive manufacturing (AM) is one of the key challenges in terms of structural integrity and finish quality of printed components. Estimating the residual stress distribution on additively manufactured ... -
A new paradigm in process synthesis focus on design of power plants and industrial processes integrated with CO2 capture
(Journal article; Peer reviewed, 2016)Process synthesis methods have only recently been applied for the design of CO2 capture systems. At the crux of the CO2 capture process is a separation technology (sorbent, membrane or phase separation) applied to CO2/N2, ... -
A New Set of Principles for Pursuing the Lean Ideal in Engineer-to-order Manufacturers
(Journal article; Peer reviewed, 2014)For many years, lean production has been successfully applied in large companies producing high volumes of standardized products. However, companies which operate in dissimilar environments have yet to expose a suitable ...