Browsing NTNU Open by Title
Now showing items 59988-60007 of 100788
-
Modeling of a Maritime DC-distribution System Supplied from a Diode Rectifier Connected Synchronous Generator
(Master thesis, 2019)Strenge utslippsreglement har blitt introdusert i den maritime sektor av den Internasjonale Maritime Organisasjon. Ny og eksiterende teknologi er analysert med høyt fokus på å utvikle mer miljøvennlige løsninger. DC ... -
Modeling of a Microbial Fuel Cell
(Master thesis, 2007)It is clear that society worldwide must immediately begin to mitigate its environmental damage in order to sustain life on Earth. In this regard, researchers all over the global are exploring new energy efficient alternatives ... -
Modeling of a Recirculating Aquaculture System
(Master thesis, 2020)Abstract will be available on 2023-08-31 -
Modeling of a semisubmersible floating offshore wind platform in severe waves
(Journal article; Peer reviewed, 2019)Floating offshore wind platforms may be subjected to severe sea states, which include both steep and long waves. The hydrodynamic models used in the offshore industry are typically based on potential-flow theory and/or ... -
Modeling of aggregated IoT traffic and its application to an IoT cloud
(Journal article; Peer reviewed, 2019)As the Internet of Things (IoT) continues to gain traction in telecommunication networks, a very large number of devices are expected to be connected and used in the near future. In order to appropriately plan and dimension ... -
Modeling of Amine Degradation in a CO2 Absorption Column at Test Centre Mongstad
(Master thesis, 2012)Two different previously conducted oxidative degradation experiments, were used as a basis of modeling monoethanolamine-degradation reactions. Literature and previous experience was used to construct reaction equations for ... -
Modeling of Aquaculture PET Net with the Use of Finite Element Method
(Master thesis, 2013)In this master thesis the structural modeling of Polyethylene Terephthalate (PET) net panel has been done using finite element software (ABAQUS). The model was built corresponding to the net panel experiment performed by ... -
Modeling of Articulated Underwater Robots for Simulation and Control
(Chapter, 2018)This paper presents a methodology for modeling articulated underwater robots possessing a kinematic tree structure and arbitrary thruster placement. Efficient algorithms for the forward dynamics and the thruster configuration ... -
Modeling of CO2 Storage in the Smeaheia Field
(Master thesis, 2018)Carbon capture and storage, CCS, is a method that can reduce today s carbon emissions by approximately 20 %. Since the world still highly depends on the use of fossil fuel energy, this method is necessary for reaching the ... -
Modeling of Compressor Characterisics and Active Surge Control
(Master thesis, 2009)In this thesis, the compressor characteristics, being representations of the compressor pressure ratio as a function of the gas flow through the compressor, have been studied. Three different types of representations of the ... -
Modeling of Condition-based Maintenance by Competing Risks
(Master thesis, 2009)Condition-based maintenance is a preventive maintenance strategy where intervention times are determined based on knowledge of actual item condition provided by condition monitoring. In this report condition-based maintenance ... -
Modeling of decisions made by test persons in a dice task
(Master thesis, 2022)Det er antatt å være en sammenheng mellom å ta forhastede avgjørelser og å være diagnostisert med schizofreni. Noen hevder at oppgaver som omhandler sannsynlighetsresonementer utført av både friske og schizofrene deltakere, ... -
Modeling of Drain Current and Intrinsic Capacitances in Nanoscale Double-Gate and Gate-All-Around MOSFETs
(Doktoravhandlinger ved NTNU, 1503-8181; 2008:240, Doctoral thesis, 2008) -
Modeling of electric shaft used by the company Inpower AS
(Master thesis, 2015)The master thesis is a further investigation of the steady state performance of the direct connection of the permanent magnet generators and motors, used for the ship propulsion; as proposed in the specializing project ... -
Modeling of electrochemical and photoelectrochemical impedance functions for films
(Master thesis, 2014)The aim of this study was to develop mathematical models for electrochemical and photoelectrochemical impedance transfer functions for mixed conducting films. These models include electrochemical impedance spectroscopy ... -
Modeling of Electrostatics and Drain Current in Nanoscale Double-Gate MOSFETs
(Doktoravhandlinger ved NTNU, 1503-8181; 2007:162, Doctoral thesis, 2007)This work comprises a new technique for 2D compact modeling of short-channel, nanoscale, double-gate MOSFETs. In low-doped devices working in the subthreshold regime, the potential distribution is dominated by the capacitive ... -
Modeling of Failure in Large-scale Metallic Structures
(Master thesis, 2021) -
Modeling of Fatigue from Random Corrosion Pits
(Master thesis, 2015)This master thesis is a continuation of the project work Fatigue Assessment of Mechanical Components with Random Surface Defects written during the fall of 2015. Central tasks of this report has been to create a manual ... -
Modeling of fractured producer and injection in low permeability reservoir
(Master thesis, 2013)Modeling of fractured producer and injection well in low permeability reservoir