Utvikling av installasjonsprosess av "Fully Insulated Dummy Connector" på et subseagasskompresjons-anlegg
Bachelor thesis
Permanent lenke
https://hdl.handle.net/11250/2782302Utgivelsesdato
2021Metadata
Vis full innførselSamlinger
Sammendrag
Denne rapporten vil ta for seg installasjon- og avinstallasjon av tre fully insulateddummy connectors (FIDC) på gass-kompresjonsanlegget Jansz-Io Subsea Compressionproject. Den initielle problemstillingen gitt av teknologiselskapet Aker Solutionsbesto av å løse problemet med å få installert FIDC’ene i et trangt arbeidsområdeunder et overheng av en ROV på 1300m havdyp. Dette er et nytt problem forAker Solutions, og har dermed ikke en tidligere løsning på det tidspunktet oppgavenblir skrevet. Den foreslåtte løsningen i denne rapporten er at FIDCene heisesned på vaier og lander på et skinnesystem. En ROV blir brukt til å dytte FIDCene tilde er plassert rett over undervanns-koblingene. Deretter heises FIDCene ned i riktigposisjon med en spesiallaget heis som opereres av en ROV. Videre blir FIDCenejekket fast med et av Aker Solutions egne verktøy, og låst fast med en ROV-styrtbolteskåte. Hovedinnovasjonen i denne rapporten er heisen som benytter seg avsnekkegir- og tannhjul/tannstang teknologi, som vil gjøre det mulig for en ROVå jekke på plass FIDC-ene i sine respektive undervanns-koblinger. Denne teknologienkan også brukes i fremtidige installasjoner som har liknende utfordringermed installasjoner i subsea miljøet. Idéene til denne prosessen har blitt utvikletgjennom iterative diskusjoner med oppdragsgiveren Aker Solutions, andre eksperterinnenfor NTNU/SINTEF og veiledere. I tillegg til detaljerte diskusjoner rundtløsningen, har løsningene blitt visualisert i Solidworks, både som tegninger avkomponentene og animasjoner av sammensetningen og prosessen. This report will explain the concept of installation and deinstallation of three fullyinsulated dummy connectors (FIDC) on the gas compression facility Jansz-Io. Theinitial development topic given by the technology corporation Aker Solutions, consistedof the installation of a FIDC in a tight work area. The installation is done bya ROV under an overhang at a depth of 1300m below sea level. This was a newchallenge for Aker Solutions and there is no proper solution for this problem atthe present time. The suggested solution suggests that the three FIDC mountedon a plate will be hoisted down by cable and will rest on a track system. A ROVwill be used to push the FIDC into the right positions above the female wet mates.To connect to the wet mates a custom made lift system, that is operated by theROV, will lower the FIDC into the wet mates. To get the correct mating force, oneof Aker Solutions’ own tools are used. After the correct mating force is applied,a bolt lock mechanism is used to lock the contraption in place with the correctmating force. The key inovation in this report is the lift that lifts and lowers theFIDC into the wet mate connectors. It is based on a worm gear, and rack & piniontechnology, which makes it possible to lower the FIDC in place using an ROV. Thistechnology can be used in future installations, with similar challenges. The ideasfor the solutions has been developed through iterative discussions with the projectowners Aker Solutions, other experts within NTNU/SINTEF and supervisors.In addition to detailed discussions of the solution, the solution has been visualizedin Solidworks, both as drawing of the components as well as animation of partsand processes.