Blar i Institutt for materialteknologi på tittel
Viser treff 1448-1467 av 2504
-
Microstructure and enhanced mechanical properties of an Mg-10Gd-2Y-0.5Zr alloy processed by cyclic extrusion and compression
(Journal article; Peer reviewed, 2011)The evolution of microstructure and texture of an extruded GW102K Mg alloy processed by cyclic extrusion and compression (CEC) at 450 °C were investigated. Tensile tests were performed at room temperature and strain rate ... -
Microstructure and Mechanical Properties of 6013 Aluminum Alloy Processed by a Combination of ECAP and Preaging Treatment
(Journal article; Peer reviewed, 2017)Microstructure and mechanical properties of a 6013 Al-Mg-Si-Cu aluminum alloy processed by a combination of equal channel angular pressing (ECAP) and preaging treatment were comparatively investigated using quantitative ... -
Microstructure and mechanical properties of Al-xMg alloys processed by room temperature ECAP
(Journal article; Peer reviewed, 2012)Microstructure development and mechanical properties of Al–xMg alloys (x = 0, 1, 5–10 wt%), processed by ECAP at room temperature, have been investigated. The results show that the microstructures of Al–xMg alloys are ... -
Microstructure and mechanical properties of the AZ31/GW103K bimetal composite rods fabricated by co-extrusion
(Peer reviewed; Journal article, 2022)The AZ31/GW103K bimetal composite rods consisting of a soft AZ31 sleeve and a hard GW103K core were fabricated by the co-extrusion at 350 °C, 400 °C and 450 °C, and their microstructure and mechanical properties were ... -
Microstructure and Mechanical Properties of Welded AA6082 Aluminium Alloys
(Master thesis, 2016)The present work have investigated variants of an AA6082 aluminium alloy. Five different alloys with various amounts of Mn, Cr and Zr have been subjected to three homogenization procedures. After homogenization, the aluminium ... -
Microstructure And Properties Of Extruded Al-Alloys For Crash Components In Cars
(Master thesis, 2014)The demand for lightweight materials in the transport industry is fuelling the research of high performing components. Extruded aluminium profiles intended for crash components are examined in this project. The objective ... -
Microstructure and properties of nano-C and in-situ Al2O3 reinforced aluminum matrix composites processed by high-pressure torsion
(Peer reviewed; Journal article, 2021)In this study, Al-Si matrix composites reinforced with In situ Al2O3, C nanotubes (CNTs), and graphene nanoplatelets (GNPs) were prepared by ball milling, hot-isostatic pressing (HIP), and subsequent high-pressure torsion ... -
Microstructure and Properties of Wire Arc Additive Manufacturing of Inconel 625
(Journal article; Peer reviewed, 2022)In the present investigation, wire arc additive manufacturing of Inconel 625 was carried out with the cold metal transfer variant of the metal inert gas process. The heat input varied between 0.46 and 0.63 kJ/mm, which is ... -
Microstructure and texture characteristics of ZK60 Mg alloy processed by cyclic extrusion and compression
(Journal article; Peer reviewed, 2010)The microstructure and crystallographic texture characteristics of an extruded ZK60 Mg alloy subjected to cyclic extrusion and compression (CEC) up to 8 passes at 503 K were investigated. The local crystallographic texture, ... -
Microstructure Evolution and Recrystallization Resistance of a 7055 Alloy Fabricated by Spray Forming Technology and by Conventional Ingot Metallurgy
(Peer reviewed; Journal article, 2020)The effect of different fabricating processes (spray forming and conventional casting) and homogenization treatment on the microstructure of an 7055 alloy was investigated by optical microscopy (OM), scanning electron ... -
Microstructure Evolution in Super Duplex Stainless Steels Containing σ-Phase Investigated at Low-Temperature Using In Situ SEM/EBSD Tensile Testing
(Journal article; Peer reviewed, 2018)An in situ scanning electron microscope (SEM) study was conducted on a super duplex stainless steel (SDSS) containing 0%, 5% and 10% σ-phase. The material was heat treated at 850 °C for 12 min and 15 min, respectively, to ... -
Microstructure evolution of commercial pure titanium during equal channel angular pressing
(Journal article; Peer reviewed, 2010)The microstructure development of commercially pure titanium during 3 and 4 passes of equal channel angular pressing (ECAP) has been investigated in detail by optical microscopy and electron backscattered diffraction (EBSD). ... -
Microstructure in A356/AA6xxx after bimetallic casting with flux coating
(Journal article; Peer reviewed, 2019)This work focuses on bimetallic casting between A356 alloy melt and profiles of AA6xxx wrought aluminum alloys through a gravity casting process, with the aim to improve the component's mechanical properties. However, ... -
Microstructures and mechanical properties of Cu/Ti3SiC2/C/graphene nanocomposites prepared by vacuum hot-pressing sintering and hot isostatic pressing
(Journal article; Peer reviewed, 2018)Copper-graphite composite is an ideal friction material due to its good heat resistance, wear resistance and friction coefficient stability. The addition of Ti3SiC2 can improve strength, hardness and wear resistance of ... -
Microstructures and mechanical properties of nano-C and in situ Al2O3 reinforced aluminium matrix composites processed by equal-channel angular pressing
(Journal article; Peer reviewed, 2021) -
Microstructures and Properties of Aluminium-Magnesium Alloys with Additions of Manganese, Zirconium and Scandium
(Dr. ingeniøravhandling, 0809-103X; 2000:12, Doctoral thesis, 2000)The present work reports on the effect of Mn-, Zr- and Sc-additions upon hot deformation properties, recrystallization properties and mechanical properties for different temper conditions of Al-Mg alloys. It can be stated ... -
Microwave-assisted in situ laser dye incorporation into high sensitivity whispering gallery mode microresonators
(Peer reviewed; Journal article, 2022)Optical whispering gallery mode microresonators (WGM-µRs) are powerful sensitive components with many analytical applications. Here, spherical WGM-µRs have been synthesised in a single-step microwave (MW)-assisted heterophase ... -
Mikrobiell vekst og desinfisering i klatresenter
(Bachelor thesis, 2022)Sammendraget er konfidensielt -
Mikrobiell vekst og desinfisering i klatresenter
(Bachelor thesis, 2022)Sammendraget er konfidensielt.