Blar i Institutt for materialteknologi på tittel
Viser treff 639-658 av 2513
-
The effect of grain size and rolling reduction on microstructure evolution and annealing hardening response of a Mg-3Gd alloy
(Journal article; Peer reviewed, 2024)Mg-3Gd (wt.%) samples with different initial grain sizes were prepared to evaluate the grain size effect on microstructural evolution during cold rolling and subsequent annealing hardening response. The deformation behavior ... -
Effect of heat input on nanomechanical properties of wire-arc additive manufactured Al 4047 alloys
(Peer reviewed; Journal article, 2022)Heat input is one of the most important process parameters during additive manufacturing (AM). It is of great significance to understand the effect of heat input on the microstructure and nanomechanical properties, as well ... -
Effect of Hot Rolling on Grain Refining Performance of Al–5Ti–1B Master Alloy on Hot Tearing on Al–7Si–3Cu Alloy
(Journal article; Peer reviewed, 2018)It has been known experimentally that TiAl3 acts as a powerful nucleant for the solidification of aluminum from the melt; however, a full microscopic understanding is still lacking. To improve microscopic understanding, ... -
Effect of hybridization in PdAlY-(Ni/Au/Ir) metallic glasses thin films on electrical resistivity
(Peer reviewed; Journal article, 2022)Thin film metallic glasses (MGs) are promising materials for electronic applications. While the transport properties of MGs are composition dependent, the influence of hybridization on the resistivity has not been investigated ... -
The Effect of Hydrogen and Methane Containing Gases on SiC and SiO formation
(Doctoral theses at NTNU;2023:48, Doctoral thesis, 2023)The production of silicon is currently done in a submerged arc furnace where quartz react with carbon. This emits large amounts of CO2to the atmosphere. From a global warming perspective this is far from ideal, and ... -
Effect of Inclusion and Filtration on Grain Refinement Efficiency of Aluminum Alloy
(Journal article; Peer reviewed, 2022)It is well known that the filtration efficiency of ceramic foam filters (CFF) on aluminum melt can be significantly reduced by the addition of grain refiner particles under a high inclusion load. Also, it is usually ... -
Effect of Magnesium Addition on Removal of Impurities from Silicon by Hydrometallurgical Treatment
(Chapter, 2017)Hydrometallurgical treatment of silicon is an effective process for the removal of metallic impurities for producing solar grade silicon feedstock. In the present research, the removal of impurities from silicon is studied ... -
Effect of Magnesium Addition on Removal of Impurities from Silicon by Hydrometallurgical Treatment
(Chapter, 2017)Hydrometallurgical treatment of silicon is an effective process for the removal of metallic impurities for producing solar grade silicon feedstock. In the present research, the removal of impurities from silicon is studied ... -
Effect of marine environment on the tribology performance of materials used in lubricated rotating parts of offshore wind turbines
(Master thesis, 2012)The use of offshore wind turbines as a source of renewable energy is promising. However, many challenges have to be solved before they will be cost effective. The operation time, without any maintenance required, is desired ... -
Effect of mechanical depoling on piezoelectric properties of Na0.5Bi0.5TiO3 - xBaTiO3 in the morphotropic phase boundary region
(Journal article; Peer reviewed, 2018)The effect of mechanical stress on the direct piezoelectric properties of pre-poled (1 − x)(Na0.5Bi0.5)TiO3–xBaTiO3 (NBT–xBT) in the range 4% ≤ x ≤ 13% was studied in situ using a mechanical load frame. Prior to mechanical ... -
Effect of Mg content in the La3-xMgxNi9 battery anode alloys on the structural, hydrogen storage and electrochemical properties
(Peer reviewed; Journal article, 2021)The present work is focused on the studies of structure, hydrogen storage and electrochemical properties of the La3-xMgxNi9 (x = 1.0, 1.1 and 1.2) alloys as active materials of negative electrodes in the Nickel-Metal Hydride ... -
Effect of Mg on microstructure and mechanical properties of Al-Mg alloys produced by high pressure torsion
(Journal article; Peer reviewed, 2019)Al-Mg alloys are a series of low cost and low density Al alloys, which show remarkable strengthening during deformation. In this work, study of commercial purity Al, Al-0.5Mg and Al-4.1Mg alloys was carried out to investigate ... -
The Effect of Microstructure and Cu Content on Corrosion Behavior of 6060 Aluminum Alloy
(Master thesis, 2018)AlMgSi alloys have gained more popularity in the automobile industry in recent years due to attractive properties such as good corrosion resistance, machineability and high strength-to-weight ratio. Cu is commonly added ... -
Effect of microstructure on precipitation of β-Mg2Si during cooling of Al-Mg- Si alloys
(Doctoral theses at NTNU;2024:228, Doctoral thesis, 2024)Processing of Al-Mg-Si alloys requires tight control of the various secondary Mg-Si phases that form during the processing steps. In this regard, the cooling stage after homogenisation is a crucial step because of the ... -
Effect of microstructure on the corrosion resistance of duplex stainless steels: Materials performance maps
(Journal article; Peer reviewed, 2017)Although super duplex stainless steels (25Cr SDSS) are extensively used in oil and gas production due to their excellent combination of mechanical properties and corrosion resistance they are susceptible to the precipitation ... -
Effect of Microstructure on the Performance of Corrosion Resistant Alloys
(Master thesis, 2015)Corrosion by pitting in aluminum alloys is a very complex process that can be affected by various factors such as chemical composition and microstructure of the alloys. The electrochemistry and distribution of second phases ... -
Effect of Microstructure on the Precipitation of β-Mg2Si during Cooling after Homogenisation of Al-Mg-Si Alloys
(Peer reviewed; Journal article, 2024)For Al-Mg-Si alloys, cooling after homogenisation is a crucial step because the precipitation of the equilibrium β-Mg2Si phase determines the processing capabilities in subsequent steps, as well as the subsequent precipitation ... -
Effect of Mn and cooling rates on α-, β- and δ-Al–Fe–Si intermetallic phase formation in a secondary Al–Si alloy
(Journal article; Peer reviewed, 2019)Secondary Al–Si alloys Al7.1Si(1.5-xMn)Fe(xMn)Mn with xMn = 0, 0.3, 0.375, 0.6, 0.75 at.% have been solidified with different cooling rates: 0.05 K/s, 1.4 K/s, 11.4 K/s and 200 K/s. In the ternary alloy with xMn = 0 at.%, ... -
Effect of Mn and Dispersoids on Grain Structure, Mechanical Properties and Crush Behavior of Extruded AA6082 Alloys
(Master thesis, 2015)In this study five different variants of an AA6082 aluminum alloy were investigated. The alloys have various amounts of Mn (0.006-1.172 wt%) and are homogenized in two different ways. After homogenization the billets got ... -
Effect of Moisture, Hydrogen, and Water–Gas Shift Reaction on the Prereduction Behavior of Comilog and Nchwaning Manganese Ores
(Peer reviewed; Journal article, 2022)The ore–gas reactions in the prereduction zone in a ferromanganese furnace are largely decisive of the overall energy efficiency, carbon consumption, and climate gas emissions in ferromanganese production. An increased ...