Blar i Institutt for materialteknologi på tittel
Viser treff 480-499 av 2562
-
Degradering av en 4G-kunstgressbane: Effekt av vinterdrift og UV-stråling
(Bachelor thesis, 2020)I arbeidet ble effekt av vinterdrift og UV-stråling på en 4G-kunstgressbane undersøkt ved salt- og UV-eksponering av kunstgressfiber og salteksponering av backing. Oppgaven er en del av Senter for idrettsanlegg og teknologi ... -
Degradering av mikromønster på bruddflater av ulegert stål som følge av korrosjon
(Bachelor thesis, 2020)Denne oppgaven ble gjort i samarbeid med DNV GL. Hensikten med oppgaven var å se på degradering av mikromønster på bruddoverflater som følge av korrosjon ved ulike tidsintervaller. Korrosjon av bruddoverflater kan være et ... -
Degradering av mikromønstre på bruddflater av lavlegert stål som følge av korrosjon i sjøvann
(Bachelor thesis, 2020)Formålet med arbeidet har vært å se på degradering av mikromønster på bruddflater som følge av korrosjon. Tre ulike rensemiddel for å fjerne korrosjonsprodukter ble testet; Alconox,10% og 20% inhibert HCl. Hensikten var å ... -
Degreasing of aluminum turnings and implications for solid state recycling
(Chapter, 2010)With the global warming being of concern, recycling of aluminum by new solid-state recycling techniques instead of conventional remelting and subsequent refining processing has been taken into account. Solid-state recycling ... -
Dekommisjonering av olje- og gassinstallasjoner: Gjenbruk og resirkulering av stål og betong fra et sirkulærøkonomisk perspektiv
(Bachelor thesis, 2024)Hensikten med dette prosjektet var å identifisere og bestemme hvordan stål og betong fra olje- og gassinstallasjoner på best mulig måte kan gjenbrukes og resirkuleres. Dette ble utført i sammenheng med den sirkulære modellen ... -
Delamination kinetics of thin film poly(acrylate) model coatings prepared by surface initiated atom transfer radical polymerization on iron
(Journal article; Peer reviewed, 2018)Living radical polymerization is often considered as an unsuitable method of surface modification for reactive metals such as iron. Necessary noble metal catalyst systems may react with the surface to be modified, causing ... -
Demulsification Methods for Oil and Water Emulsions
(Bachelor thesis, 2021)Det er viktig å skille olje- og vannemulsjoner for å kunne oppnå konsentrerte råoljeprodukter. Gravitasjonsseparasjon er den vanligste metoden, men ikke den mest effektive. Separasjonsmetoder som elektrokoalesens, sentrifuge ... -
Dense Oxygen Separation Membrane Materials —Thermal and Chemical Expansion of La1xSrxMO3-δ (M = Fe, Co) and Tape Casting and Mechanical Properties of La2NiO4+δ
(Doktoravhandlinger ved NTNU, 1503-8181; 2013:367, Doctoral thesis, 2013) -
Densification of Biocarbon and Its Effect on CO2 Reactivity
(Peer reviewed; Journal article, 2021)Charcoal is an interesting reducing agent because it is produced from biomass which is renewable and does not contribute to global warming, provided that there is a balance between the felling of timber and growth of trees. ... -
Densification of charcoal by thermal decomposition of methane
(Master thesis, 2022)I dette prosjektet ble densifisering av trekull gjennom dekomponering av metan undersøkt. Totalt ble 6 prøvesett analysert, hver med en vekt på ca 350 g. De ulike gradene av densifisering var 10.3 , 11.1 , 24.0 og 29.7 ... -
Depolarized gas anodes for electrowinning in molten salts
(Doktoravhandlinger ved NTNU, 1503-8181; 2011:130, Doctoral thesis, 2011) -
Depolarized SnO2-based gas anodes for electrowinning of silver in molten chlorides
(Journal article; Peer reviewed, 2013)SnO2-based porous anodes were prepared and the behavior of gas bubbles on the porous anodes with different original coarse grain size, immersed in ethanol to simulate molten chlorides, was primarily investigated. SnO2-based ... -
Deposition and reduction of manganese dioxide on alternative anode materials in zinc electrowinning
(Dr. ingeniøravhandling, 0809-103X; 2000:19, Doctoral thesis, 2000) -
Deposition of phase pure KNN thin Films
(Master thesis, 2016)Piezoelectric and ferroelectric materials have a wide range of applications, from touch and heat sensors to LCDs and actuators in MEMS. Lead zirconate titanate (PZT), is the most well-known ferroelectric material, and is ... -
Deposition of silica nanoparticles onto alumina measured by optical reflectometry and quartz crystal microbalance with dissipation techniques
(Journal article; Peer reviewed, 2014)Understanding of the interactions between particles and the substrate is important for successful sol–gel deposition of thin films. We have studied the deposition of silica nanoparticles on alumina coated surfaces in aqueous ... -
Deposition of Thin Film Electrolyte by Pulsed Laser Deposition (PLD) for micro-SOFC Development
(Master thesis, 2012)Optimalization of PLD deposition of YSZ for micr-SOFC electrolyte applications by varying deposition pressure and target-substrate distance.Substrate used was Si-based chips and wafers (large area PLD), and the substrate ... -
Depth profiling at a steel-aluminum interface using slow-flow direct current glow discharge mass spectrometry
(Journal article; Peer reviewed, 2021) -
Design and manufacture of Portland cement Application of statistical analysis
(Doktoravhandlinger ved NTNU, 1503-8181; 2011:196, Doctoral thesis, 2011)The purpose of the work is to enable design and manufacture of cement with emphasis on the quality and the properties of cement. Data used in the design and manufacture were collected from predictions of properties and ... -
Design of multi-luminescent silica-based nanoparticles for the detection of liquid organic compounds
(Journal article; Peer reviewed, 2024)Tracer testing in reservoir formations is utilised to determine residual oil saturation as part of optimum hydrocarbon production. Here, we present a novel detection method of liquid organic compounds by monodisperse SiO2 ... -
Design og fabrikasjon av undervannsstrukturer - Sveisegeometri og inspeksjonskategori - påvirkning på fabrikasjonskostnader
(Bachelor thesis, 2019)Denne bacheloren omhandler design og fabrikasjon av subsea-strukturer. Det vil bli fokusert på mulighetene for å redusere produksjonskostnader på hovedståletet til en manifold. For å oppnå dette blir det sett på mulighetene ...