Blar i Institutt for maskinteknikk og produksjon på tittel
Viser treff 245-264 av 3992
-
Analysing environmental impacts from waste, water and wastewater infrastructure in the early phase planning of new urban settlements
(Doktoravhandlinger ved NTNU, 1503-8181; 2013:120, Doctoral thesis, 2013)Reducing the level of greenhouse gas emissions is on the policy agenda in many countries, including Norway. Human settlements draw on resources and cause emissions in many different ways, for example through direct energy ... -
Analysing the Main Standards for Climate-Induced Mechanical Risk in Heritage Wooden Structures: The Case of the Ringebu and Heddal Stave Churches (Norway)
(Peer reviewed; Journal article, 2022)Studying, controlling and extrapolating the indoor microclimate of historical buildings have always been at the forefront among numerous preventive conservation strategies, especially in case of buildings made of organic ... -
“Analysis and Improvement of Internal Logistics in the Library Sector through Autonomous Mobile Robots: A Case Study of Trondheim Public Library”
(Master thesis, 2024)Denne avhandlingen er resultatet av et samarbeid mellom NTNUs Institutt for maskin- og industriell teknologi og Trondheim folkebibliotek (TPL). Den er en del av det flerårige prosjektet SmartLIB, som fokuserer på utviklingen ... -
Analysis and modelling of recent large floods on the river Gaula
(Master thesis, 2015)In order to study the flood from 2009, 2010 and 2011 that have been impacting the Gaula waterway, a hydrological and operational model have been built. A brief description of the study is given as an introduction, followed ... -
Analysis and optimisation of books flow among branches through simulation: the case of Trondheim’s Public Library
(Master thesis, 2022)Denne oppgaven omhandler analyse og optimalisering av strømmene av bøker som genereres mellom de ulike stedene til Trondheim folkebibliotek, Trondheim folkebibliotek, som ligger i Trondheim, en by i Nord-Norge. ... -
Analysis of a Novel Wedge-Burst Test Design with Integrated Load Cells: A Comparison to the Split-Disk Test and an Investigation of the Effects of an Elastomeric Distributor
(Master thesis, 2020)En wedge-burst (kile-burst) test med integrerte lastceller har blitt sammenlignet med en split-disk test ved hjelp av finite element analyser (FEA). Oppførselen til sylinderspenningen og den kalkulert spenning for begge ... -
Analysis of a Pre-Tensioning Concept for a Floating Bridge Support Structure
(Master thesis, 2015)This thesis regards a pretensioning procedure for a large and slender support structure planned built below a floating bridge. First and foremost, global aspects are discussed with little consideration for local phenomenons. ... -
Analysis of Aluminium Hot Forging
(Doktoravhandlinger ved NTNU, 1503-8181; 2005:3, Doctoral thesis, 2005) -
Analysis of camshaft gear transmission for a ship engine
(Master thesis, 2015)This thesis investigates the dynamic behavior of a spur gear pair. The gears studied are somewhat similar to the ones found in Bergen Engines medium-speed diesel engine with regards to design, but some assumptions have ... -
Analysis of Challenges associated with Implementing Agile Project Management
(Master thesis, 2011)The purpose of this study was to investigate and analyze challenges associated with contracting, subcontracting, estimation process, risk management and success measurement. Qualitative method was applied in this study. ... -
An Analysis of CII's 10-10 Performance Assessment Program in Statnett
(Master thesis, 2017)The Constructions Industry Institute has developed a system known as the 10-10 Performance Assessment Program to meet the growing demands for a comprehensive performance measurement system in the construction sector that ... -
Analysis of Compact Separation Systems and Experimental Study of Centrifugal Separation in Helically Coiled Pipes
(Master thesis, 2015)The offshore petroleum industry is experiencing challenges as exploration and production are forced towards remote and deep reservoirs, combined with high cost-efficiency demands. Topside facilities struggle with limited ... -
Analysis of domino scenarios in chemical and process facilities operating in harsh environmental conditions
(Chapter, 2018)In the framework of chemical and process industry, accidental fires may lead to damages to equipment with severe consequences and possible domino effects. The availability and effectiveness of safety measures, aimed at ... -
Analysis of ESAFORM 2021 cup drawing benchmark of an Al alloy, critical factors for accuracy and efficiency of FE simulations
(Peer reviewed; Journal article, 2022)This article details the ESAFORM Benchmark 2021. The deep drawing cup of a 1 mm thick, AA 6016-T4 sheet with a strong cube texture was simulated by 11 teams relying on phenomenological or crystal plasticity approaches, ... -
Analysis of Methods for Handling of Cemented Casing in Subsea Wells
(Master thesis, 2013)Plug and abandonment (P\&A) of subsea wells often involves removal of steel casing. In some parts of the well the casing is cemented in place making the operation of retrieving the casing more complex. The conventional ... -
Analysis of the Fatigue Behavior of 3D-Printed Maraging 300 Steel
(Master thesis, 2020)3D-printing er en fremstillings teknologi som kan fremstille strukturelle deler laget av metall gjennom lag for lag oppbygging. Målet med dette studiet er å undersøke data fra utmattelses tester med to Maraging 300 stål ... -
Analysis of the plastic zone near the crack tips under the uniaxial tension using ordinary state‐based peridynamics
(Journal article; Peer reviewed, 2018)In this paper, the plastic model of ordinary state‐based peridynamics is established. The size and shape of plastic zone around crack tips with the different inclination angles are simulated using ordinary state‐based ... -
Analysis of Vibration Data and Investigation of Models to Support Maintenance Decision of Rotating Components
(Doctoral theses at NTNU;2024:5, Doctoral thesis, 2024)This PhD project focuses on analysis of vibration data and investigation of mathematical models to support maintenance decision of rotating components and more specifically roller bearings. The PhD work generally consists ... -
Analysis Software for Calculation of Cross-Section Parameters for Complex Beam Cross-Sections
(Master thesis, 2016)Cross-sectional parameters for complex cross-sections are very difficult to calculate by analytical means. Dynamic calculations of aircraft and wind turbines often make use of beam elements for the wings and turbine blades, ... -
Analytic Assessment of Safety Instrumented Systems Operating in High-Demand Mode
(Master thesis, 2015)The pervasive presence of safety instrumented systems in the process industry indicate the growing need for reliable loss prevention to the minutest degree. The backdrop towards addressing this need is by drawing up a ...