Blar i Institutt for maskinteknikk og produksjon på tittel
Viser treff 3524-3543 av 3992
-
Systems-Theoretic Process Analysis (STPA) Applied to the Operation of Fully Autonomous Vessels
(Master thesis, 2018)The objective of this master thesis is to assess the feasibility of using the STPA for hazard identification and assessment of complex and fully autonomous operating systems. As a continuous work from autumn 2017, this ... -
T-stress effects on fatigue crack growth – Theory and experiment
(Journal article, 2018)The effects of specimen geometry on the fatigue crack growth rate and the number of elapsed cycles have been investigated experimentally and theoretically for Al 7075-T6 using four different cracked specimens with positive ... -
Tactical and Operational Issues in a Hybrid MTO-MTS Production Environment: The Case of Food Production
(Chapter, 2013)Hybrid production environments that combine MTO and MTS strategies have emerged to enable production systems to better respond to changes in consumer and market demand. This paper discusses some of the tactical and operational ... -
Taguchi Optimization of Parameters for Feedstock Fabrication and FDM Manufacturing of Wear-Resistant UHMWPE-Based Composites
(Peer reviewed; Journal article, 2020)It is believed that the structure and properties of parts fabricated by additive (i.e., non-stationary) manufacturing are slightly worse compared to hot pressing. To further proceed with improving the quality of Fused ... -
Tailoring Biocomposites with Reduced Water Uptake for 3D Printing
(Master thesis, 2017)In this study, two different grades of bioPE, with a varying melt flow index (MFI) were tested for making biocomposites reinforced with wood fibre. A low MFI was found to be more adequate for the manufacturing. Filaments ... -
Takt-time control in high-mix/low-volume production
(Master thesis, 2015)Purpose The purpose of this thesis is to develop a spreadsheet tool for takt planning in a high-mix/low-volume (HMLV) environment. Ultimately, the objective is to develop tool that the production planner can use to test ... -
Tangential strain‐based criteria for mixed‐mode I/II fracture toughness of cement concrete
(Journal article; Peer reviewed, 2018)Experimental and theoretical works are performed on the mixed‐mode I/II brittle fracture of cement concrete tested by edge cracked semicircular bend specimens. Theoretical background of the traditional fracture criteria ... -
Tape winding angle influence on subsea cable sheathing fatigue performance
(Peer reviewed; Journal article, 2020)A fundamental component of subsea power cables is the thin galvanized steel tape winded around the dielectric and sheathing layer in order to prevent permanent thermal cycling induced deformation. The pressure state induced ... -
Task Programming of Redundant Industrial Robots: A Virtually Extended Null Space Formulation Verified Through Obstacle Avoidance
(Master thesis, 2012)Industrial robots are an important part of modern automation and are used in a variety of applications such as handling, welding, painting and assembling. They have normally six degrees of freedom to provide an arbitrary ... -
A Taxonomy for Engineering Change Management in Complex ETO Firms
(Chapter, 2020)Abstract: In this paper, we study a specific type of Engineer-to-Order (ETO) firms called Complex ETO characterized by one-of-a-kind products with high complexity and low volumes. Such firms are at high risk of encountering ... -
TCN-based Machine Learning Analysis of DOFS Data for Subsea Acoustic Source Localization
(Master thesis, 2023)Distribuerte Optiske Fibersensorer (DOFS) tilbyr høyoppløselige tøynings- og temperaturmålinger med lang rekkevidde og som har en minimal innvirkning på måleobjektene, og derfor i økende grad benyttes for måling av både ... -
Team and Research Based Learning Methods Applied in Multidisciplinary Marine Engineering Education
(Journal article; Peer reviewed, 2019)This paper presents an integrated team-based, and research-based learning approach utilized in lecturing multidisciplinary marine engineering courses. The approach is exemplified during one month Ocean Engineering Summer ... -
Technical health, remaining useful life and life extension of subsea equipment
(Doctoral thesis at NTNU;2015:136, Doctoral thesis, 2015)This PhD thesis proposes concepts, tools and processes for analyses of technical health and remaining useful life (RUL) for decision-making regarding life extension of subsea equipment. The thesis is the outcome of the ... -
Technology for Tidal Turbine Blades
(Master thesis, 2010)The recent years have seen an increase in the interest in and need for renewable energy due to changes in the climate. Wind and tidal turbines are important sources of renewable energy, and the blades of these turbines are ... -
TECHNOLOGY QUALIFICATION OF EQUIPMENT IN SUBSEA PRODUCTION SYSTEMS
(Master thesis, 2012)Development of new technology has always been an important activity for the oil and gas in- dustry. New technologies can streamline the production, improve the recovery rate and provide economic benefits. The implementation ... -
Technology Roadmap to Support Production Expansion in an SME - A Case Study
(Master thesis, 2017)Micro, small and medium-sized enterprises (SMEs) can be seen as the backbone of the European economy as they drive economic growth and job creation, as well as ensuring social stability. The companies are evolving in a ... -
Teknisk og økonomisk beregning og design av mobile kjøleanlegg for bygg som ikke har kjøleanlegg for ventilasjonsanlegget, ved bruk av smeltevarme fra is
(Bachelor thesis, 2020)I de senere år har sommertemperaturene i Norge vært over historiske normaltemperaturer. Dette har medført utfordringer med for høye temperaturer innendørs i bygninger. Spesielt har sykehjem, noe som også har vært tema i ... -
Teknologikvalifikasjon av flensforbindelse for undervannsproduksjonssystemer: Maskinert fra smidd stang i dupleks rustfritt stål
(Master thesis, 2014)API Spec 17D (2011) spesifiserer at flenser for undervanns brønnhode- og juletreutstyr skal være smidd, dersom utstyret går inn under spesifikasjonsnivå PSL 3 eller PSL 3G. Videre spesifiseres det i ASTM A182/A182M (2013) ... -
Teknologisk og økonomisk potensial for tilstandsovervåkning av transformatorstasjon
(Bachelor thesis, 2021)I vår bacheloroppgave går vi frem for å kartlegge potensialet for implementering av tilstandsovervåkning ved en transformatorstasjon. Kartlegginga vil foregå på én av Haugaland Kraft Nett sine transformatorstasjoner. De ... -
Telemanipulation for Remote Maintenance.
(Master thesis, 2022)Denne oppgaven vil hovedsakelig fokusere på et filterbytte ved hjelp av en KR16 robotmanipulator. Denne manipulatoren vil utføre et enkel plukk og plasser, og dette vil bli utført gjennom kommandoer. Disse kommandoene vil ...