Blar i Publikasjoner fra CRIStin - NTNU på tittel
Viser treff 17903-17922 av 37703
-
Influence of the solute concentration on the anelasticity in Mg-Al alloys: A multiple-approach study
(Journal article; Peer reviewed, 2019)The anelastic mechanical response caused by complex twinning-detwinning processes interacting with dislocation slip in Mg and its alloys is ubiquitous for their deformation behavior. A rare blend of advanced in-situ ... -
Influence of the surgical team activity on airborne bacterial distribution in the operating room with mixing ventilation system: A case study at St. Olavs Hospital
(Peer reviewed; Journal article, 2021)Background Operating rooms (ORs) have strict requirements regarding cleanliness. While existing standards concerning the ventilation and staff guidelines are theoretically sufficient to subvert the threats posed by ... -
Influence of the upstream cylinder and wave breaking point on the breaking wave forces on the downstream cylinder
(Chapter, 2017)The interaction of breaking waves with marine structures involves complex free surface deformation and instantaneous loading on the structural members. A typical offshore platform or a coastal structure consists of several ... -
The influence of thermal diffusion on water migration through a porous insulation material
(Journal article; Peer reviewed, 2024)Excess water on pipes and equipment under porous insulation materials can lead to undesired corrosion. This work aims to clarify to what extent thermal diffusion affects the migration of water inside insulation materials ... -
Influence of thermal zoning and electric radiator control on the energy flexibility potential of Norwegian detached houses
(Journal article; Peer reviewed, 2019)Energy flexibility of buildings can be used to reduce energy use and costs, peak power, CO2eq- emissions or to increase self-consumption of on-site electricity generation. Thermal mass activation proved to have a large ... -
Influence of thermomechanical processing sequence on properties of AA6082-IF steel cold roll bonded composite sheet
(Journal article; Peer reviewed, 2018)Cold roll bonded tri-layered composites consisting of AA6082 and IF steel have been produced. The goal was to find the optimal sequence of solutionizing, aging and rolling, for obtaining good bond strength and at the same ... -
Influence of Tip Speed Ratio on Wake Flow Characteristics Utilizing Fully Resolved CFD Methodology
(Journal article; Peer reviewed, 2017)Dominant flow structures in the wake region behind the turbine employed in the Blind Test campaign [1], [2] is investigated numerically. The effect on the wake configuration at variable operating conditions are studied. ... -
Influence of Transglutaminase (TGase) Enzyme on Mechanical and Bioactive Porperties of Crayfish Protein Gels
(Journal article; Peer reviewed, 2017)Functional and bioactive properties of crayfish meat convert their surpluses in an excellent alternative for the development of food products. Thus, protein dispersions were subjected to a thermal treatment, obtaining a ... -
Influence of tungsten on passivity breakdown and repassivation of 25CR super duplex stainless steel
(Journal article; Peer reviewed, 2018)Super duplex stainless steels are ferritic-austenitic stainless steels with 25 wt% Cr and a pitting resistance equivalent (PRE) ≥ 40. Even though other elements, such as Cr and Mo, have been studied in much more detail ... -
Influence of Turbocharger Inertia and Air Throttle on Marine Gas Engine Response
(Journal article, 2021)Due to the current emission legislation, improving the marine propulsion system performance has received considerable notice. Employing natural gas as the primary energy source presented remarkable attention in the lean-burn ... -
Influence of variability and uncertainty of wind and waves on fatigue damage of a floating wind turbine drivetrain
(Peer reviewed; Journal article, 2021)This study investigates the effect of variability and uncertainty of wind and wave conditions on the short-term fatigue damage of a 10-MW floating wind turbine drivetrain. Global dynamic responses of a semi-submersible ... -
Influence of Viscosity and Non-Linearities in Predicting Motions of a Wind Energy Offshore Platform in Regular Waves
(Peer reviewed; Journal article, 2018)Motion prediction of floating bodies in waves represents one of the most challenging problems in naval hydrodynamics. The solution of the seakeeping problem involves the study of complex non-linear wave-body interactions ... -
The influence of visions on cooperation among interest organizations in fragmented socio-technical systems
(Journal article; Peer reviewed, 2023)The paper shows that visions of the future can be used as a predictor of cooperation and division between actors in their efforts to shape the institutional environment, specifically policy in socio-technical systems. ... -
Influence of voltage harmonics on transformer no-load loss measurements and calculation of magnetization curves
(Journal article; Peer reviewed, 2017)This paper investigates the voltage distortion phenomenon during no-load testing of transformers, its influence on no-load loss calculations, and a novel measurement technique that is unaffected by harmonics for obtaining ... -
Influence of Wax Inhibitor Molecular Weight on Solution Crystallization and Rheology of Monodisperse Waxes
(Peer reviewed; Journal article, 2021)Molecular weight fractionation via stepwise precipitation or chain scission is performed on four pour point depressant polymers to study the pour point reduction mechanism. An homologous series of model oils is prepared ... -
Influence of wax inhibitor molecular weight: Fractionation and effect on crystallization of polydisperse waxes
(Journal article; Peer reviewed, 2019)The influence of wax inhibitor molecular weight on wax crystallization was investigated in three steps: (1) Wax inhibitor fractionation via stepwise precipitation or ultrasonic disintegration, (2) characterization of ... -
The Influence of Wedge Angle, Feedstock Color, and Infill Density on the Color Difference of FDM Objects
(Peer reviewed; Journal article, 2021)The surface appearance in additive manufacturing (AM) has attracted attention in recent years due to its importance in evaluating the quality of 3D printed structures. Fused Deposition Modeling (FDM), also known as Fused ... -
The Influence of Wedge Angle, Feedstock Color, and Infill Density on the Color Difference of FDM Objects
(Peer reviewed; Journal article, 2021)The surface appearance in additive manufacturing (AM) has attracted attention in recent years due to its importance in evaluating the quality of 3D printed structures. Fused Deposition Modeling (FDM), also known as Fused ... -
Influence of Weight-on-Bit on Percussive Drilling Performance
(Peer reviewed; Journal article, 2020)A phenomenological model for percussive drilling systems is proposed in this paper to explain the experimentally demonstrated existence of an optimal weight-on-bit (WOB), for which the rate of penetration (ROP) is maximized. ... -
Influence of winding layout and airgap length on radial forces in large synchronous hydrogenerators
(Chapter, 2017)This paper investigates the flux density and radial force spatial harmonics in large salient pole synchronous hydro-generators. Vibration due to magnetic forces are mainly caused by low order harmonics in the airgap flux ...