Blar i Institutt for materialteknologi på tittel
Viser treff 2395-2414 av 2540
-
Thermodynamic and Kinetic Behavior of B and Na Through the Contact of B-Doped Silicon with Na2O-SiO2 Slags
(Journal article; Peer reviewed, 2013)Boron (B) is the most problematic impurity to be removed in the processes applied for the production of solar grade silicon. Boron removal from liquid silicon by sodium-silicate slags is experimentally studied and it is ... -
A Thermodynamic Assessment of the Chemical Durability of Refractory Lining in Anode Baking Furnaces
(Journal article, 2016) -
Thermodynamic assessment of the Mo-S system and its application in thermal decomposition of MoS2
(Journal article, 2018)The Mo-S system is crucial to extractive metallurgy, tribology, and various possible applications in design and fabrication of novel two-dimensional (2D) materials. First-principles calculations were utilized to compute ... -
Thermodynamic Behavior and Mass Transfer Kinetics of Boron Between Ferrosilicon and CaO-SiO2 Slag
(Journal article; Peer reviewed, 2017)Equilibrium distribution and transport kinetics of boron between ferrosilicon and calcium silicate slag were investigated through experimental study. A 50 pct CaO-50 pct SiO2 slag (by weight) was held for different durations ... -
Thermodynamic Insight in Design of Methanation Reactor with Water Removal Considering Nexus between CO2 Conversion and Irreversibilities
(Journal article; Peer reviewed, 2021)The inevitable nexus between energy use and CO2 emission necessitates the development of sustainable energy systems. The conversion of CO2 to CH4 using green H2 in power-to-gas applications in such energy systems has ... -
Thermodynamic Study of B and P Distribution in Slag Refining Treatment
(Master thesis, 2019) -
Thermodynamics of Boron Removal from Silicon Using CaO-MgO-Al2O3-SiO2 Slags
(Journal article; Peer reviewed, 2018)Slag refining is one of few metallurgical methods for removal of boron from silicon. It is important to know the thermodynamic properties of boron in slags to understand the refining process. The relation of the distribution ... -
Thermoelectric properties of A-site deficient La-doped SrTiO3 at 100–900 °C under reducing conditions
(Journal article; Peer reviewed, 2019)Lanthanum doped strontium titanate is a potential n-type thermoelectric material at moderate and high temperatures. (La0.12Sr0.88)0.95TiO3 ceramics were prepared by two different routes, conventional sintering at 1500 °C ... -
Thermoelectric Properties of A-site Deficient Lanthanum Substituted Strontium Titanate
(Master thesis, 2014)The n-type thermoelectric material (La0.12Sr0.88)0.95TiO3-delta was sintered with the spark plasma sintering method at different temperatures and pressures. This was done to reduce the thermal conductivity of the material ... -
Thermoelectric Properties of Ca3Co2−xMnxO6 (x = 0.05, 0.2, 0.5, 0.75, and 1)
(Journal article; Peer reviewed, 2019)High-temperature instability of the Ca3Co4−yO9+δ and CaMnO3−δ direct p-n junction causing the formation of Ca3Co2−xMnxO6 has motivated the investigation of the thermoelectric performance of this intermediate phase. Here, ... -
Thermoelectric properties of Cu2Se1−xTex solid solutions
(Journal article, 2018)Binary Cu2Se and Cu2Te have gained great attention recently because of their interesting and abnormal physical properties, such as ultralow thermal conductivity, high carrier mobility, large effective mass of carriers and ... -
Thermoelectric properties of non-stoichiometric CaMnO3-d composites formed by redox-activated exsolution.
(Journal article; Peer reviewed, 2019)A novel synthesis route for preparing well-defined composites based on CMO (CaMnO3) has been established taking advantage of the unique phase relations in the system Ca-Mn-O at reducing- and oxidizing atmosphere, respectively. ... -
Thermoelectrochemical Cell with Molten Carbonate Electrolyte
(Journal article, 2017)Industrial processes for production of metals and alloys by metallurgical and electrochemical methods generate a lot of heat due to irreversible losses. The waste heat should be used to generate electricity. Commercial ... -
Thermogravimetric Analysis of Thermal Insulating Materials Exposed to Sodium Vapor
(Journal article; Peer reviewed, 2019)The bottom thermal insulating layer in aluminum electrolysis cells is normally well protected from chemical attacks by a refractory layer. However, autopsies of spent cathode lining have shown that sodium vapor may reach ... -
Thermomechanical processing of an AA6082 - IF steel cold roll bonded composite material
(Master thesis, 2017)The work carried out in this thesis was conducted to investigate thermomechanical aspects of a steel-aluminum cold roll bonded material. The objective was to study different production parameters related to ageing of an ... -
Thickness dependent uniaxial magnetic anisotropy due to step-edges in (1 1 1)-oriented La0.7Sr0.3MnO3 thin films
(Journal article; Peer reviewed, 2019)The magnetic anisotropy of films of La0.7Sr0.3MnO3 grown on vicinal (1 1 1)-oriented SrTiO3 substrates are investigated. For temperatures above the tetragonal – cubic structural phase transition temperature of the substrate, ... -
Thin film nanoporous electrodes for the selective catalysis of oxygen in abiotically catalysed micro glucose fuel cells
(Journal article; Peer reviewed, 2016)Selective reduction of oxygen is an important property of fuel cells designed to operate in a mixed fuel environment containing both oxidizing and reducing reactants. This would be of particular importance in the design ... -
Through thickness variations of deformation texture in round profile extrusions of 6063-type aluminium alloy: experiments, FEM and crystal plasticity modelling
(Journal article; Peer reviewed, 2018)The deformation texture and its through-thickness heterogeneity for an extruded round profile are experimentally measured by the electron back-scatter diffraction technique (EBSD), and numerically modelled by coupling FEM ... -
Through thickness variations of deformation texture in round profile extrusions of 6063-type aluminium alloy: Experiments, FEM and crystal plasticity modelling
(Journal article; Peer reviewed, 2018)The deformation texture and its through-thickness heterogeneity for an extruded round profile are experimentally measured by the electron back-scatter diffraction technique (EBSD), and numerically modelled by coupling FEM ... -
TiB2-C Composite Material during aluminium electrolysis
(Master thesis, 2009)