Blar i Institutt for maskinteknikk og produksjon på tittel
Viser treff 1189-1208 av 3979
-
Effect analysis of wooden fence width on wave transmission by a numerical model
(Peer reviewed; Journal article, 2023)Wooden fences, a permeable structure, have become a nature-based solution for supporting traditional structures to restore mangrove forests along the Mekong deltaic coasts. Even though prior studies have explored a number ... -
Effect of a time-dependent magnetic field on the corrosion of Ni-Al bronze
(Journal article; Peer reviewed, 2018)Nickel-aluminum bronze (NAB) was anodically polarized in a solution of 3.5 wt% NaCl and exposed to a time-dependent magnetic field (TDMF) with an amplitude of 180 mT. The effect of a TDMF on the anodic behavior of NAB has ... -
Effect of a uniform magnetic field on corrosion of Ni-Al bronze in 3.5wt% NaCl
(Journal article; Peer reviewed, 2018)Following the observation of enhanced corrosion of parts of a seawater-immersed permanent magnet motor made from Ni-Al bronze, a laboratory study of the effect of uniform magnetic field on the corrosion of this alloy in a ... -
Effect of Adhesion on Mechanical and Tribological Properties of Glass Fiber Composites, Based on Ultra-High Molecular Weight Polyethylene Powders with Various Initial Particle Sizes
(Peer reviewed; Journal article, 2020)The aim of this study was to assess the effect of adhesion between the non-polar, ultra-high molecular weight polyethylene (UHMWPE) matrix and the glass fiber fillers of various lengths treated with the commercially available ... -
Effect of Air Storage on Stress Corrosion Cracking of ZK60 Alloy Induced by Preliminary Immersion in NaCl-Based Corrosion Solution
(Peer reviewed; Journal article, 2022)The preliminary exposure of Mg alloys to corrosion solutions can cause their embrittlement. The phenomenon is referred to as pre-exposure stress corrosion cracking (PESCC). It has been reported that relatively long storage ... -
Effect of artificial aging on Mode I delamination properties of composites with an [0/90] interface
(Master thesis, 2023)Masteroppgaven er skrevet i samarbeid med Norges teknisk-naturvitenskapelige universitet (NTNU) i Trondheim, med Andreas Echtermeyer som veileder. Målet med arbeidet og oppgaven er å få en bedre forståelse av hva slags ... -
Effect of bonding temperature and bonding time on microstructure of dissimilar transient liquid phase bonding of GTD111/BNi-2/IN718 system
(Peer reviewed; Journal article, 2022)The effect of bonding temperature and bonding time on the microstructure of transient liquid phase (TLP) bonding named GTD111 and IN718 superalloys, using a commercial Ni–B–Cr filler alloy (BNi-2) interlayer were evaluated. ... -
Effect of build thickness and geometry on quasi-static and fatigue behavior of Ti-6Al-4V produced by Electron Beam Melting
(Peer reviewed; Journal article, 2020)The geometry and material properties of additively manufactured (AM) parts are closely related in a way that any alteration in geometry of the part will change the underlying manufacturing strategy. This in turn, affects ... -
Effect of building orientation on mechanical properties of Ti6Al4V produced with powder bed fusion (PBF-LB/M)
(Master thesis, 2021)De fleste publiserte forskningsartiklene om PBF-LB/M som omhandler effekten av bygningsorienteringer, fokuserer på forskjellen mellom horisontale (0◦) og vertikale (90◦ ) bygningsorienteringer. I denne oppgaven ble det ... -
The Effect of Cellulose Nanofibres on Dewatering during Wet-Forming and the Mechanical Properties of Thermoformed Specimens Made of Thermomechanical and Kraft Pulps
(Journal article; Peer reviewed, 2023)Due to environmental concerns regarding single-use plastic materials, major efforts are being made to develop new material concepts based on biodegradable and renewable resources, e.g., wood pulp. In this study, we assessed ... -
The Effect of Co-Encapsulated GO-Cu Nanofillers on Mechanical Properties, Cell Response, and Antibacterial Activities of Mg-Zn Composite
(Peer reviewed; Journal article, 2022)Magnesium-based composites have recently been studied as biodegradable materials for preparing orthopedic implants. In this article, the graphene oxide (GO) and GO-Cu nanosystem has been homogenously dispersed as a ... -
Effect of Contamination on the Friction and Wear of Carboxylic Acids in Aqueous Lubricants
(Journal article; Peer reviewed, 2018)The friction and wear mechanisms of water-based fluids consisting of various types of carboxylic acids have been systematically investigated using a ball-on-disc tribometer on a super duplex stainless steel under boundary ... -
Effect of corrosion and fatigue on the remaining life of structures and its implication to additive manufacturing
(Journal article; Peer reviewed, 2018)This paper investigates the combined effect of corrosion and fatigue on the growth of cracks that arise from natural corrosion in steel bridges. It is shown that if these two effects need to be simultaneously analyzed. If ... -
The effect of crack insertion for FDM printed PLA materials on Mode I and Mode II fracture toughness
(Peer reviewed; Journal article, 2020)The paper presents mode I and II fracture toughness results for polylactic acid material obtained via fused deposition modeling. The tests were performed using Single Edge Notch Bend specimens loaded in four point bending: ... -
Effect of deformation processing of the dilute Mg-1Zn-0.2Ca alloy on the mechanical properties and corrosion rate in a simulated body fluid
(Peer reviewed; Journal article, 2020)Magnesium and its alloys have several competitive advantages due to their low density and the highest specific strength among modern structural metallic materials. However, the relatively low ductility and poor corrosion ... -
Effect of Die Design on Charge Welds in Aluminium Extrusion
(Chapter, 2023)Aluminium extrusions are used in more and more applications in different industrial fields, due to their properties and productivity. However, in-process scrap produced in aluminium extrusions needs to be reduced to increase ... -
Effect of different microstructural features on the hydrogen embrittlement susceptibility of alloy 718
(Journal article; Peer reviewed, 2018)Due to its high strength and acceptable corrosion resistance, Alloy 718 is a viable material for the use in subsea applications. The alloy's susceptibility to hydrogen embrittlement is however limiting its viability. In ... -
Effect of electrochemical charging on the hydrogen embrittlement susceptibility of Alloy 718
(Peer reviewed; Journal article, 2019)The susceptibility of age-hardened nickel-based Alloy 718 to hydrogen embrittlement was studied by the controlled electrochemical charging combined with slow strain-rate tensile tests (SSRT) and advanced characterization ... -
The effect of Equal Channel Angular Pressing on the stress corrosion cracking susceptibility of AZ31 alloy in simulated body fluid
(Peer reviewed; Journal article, 2020)Despite the great potential of Mg and its alloys as material for biodegradable implants, their low resistance to the simultaneous action of corrosion and mechanical stresses in the human body have hampered their use. Stress ... -
Effect of equal-channel angular pressing (ECAP) and current density of cathodic hydrogen charging on hydrogen trapping in the low-alloy steel
(Peer reviewed; Journal article, 2020)Owing to the outstanding mechanical properties, the steels and other metallic materials with the ultra-fine grained (UFG) microstructure obtained by severe plastic deformation (SPD) techniques such as equal channel angular ...