Browsing Institutt for maskinteknikk og produksjon by Title
Now showing items 2943-2962 of 4004
-
Process Analysis and Monitoring in Complex Perioperative Environments: Health Operations Management
(Doktoravhandlinger ved NTNU, 1503-8181; 2009:65, Doctoral thesis, 2009) This thesis presents studies in perioperative environments at two large university hospitals, St. Olavs Hospital in Trondheim, Norway and Massachusetts General Hospital in Boston, USA. It is submitted in partial ... -
Process design; Ensuring consistency between a piping and instrument diagram and the 3D model.
(Master thesis, 2014). -
Process Modelling Applied to Aluminium-Steel Butt Welding by Hybrid Metal Extrusion and Bonding (HYB)
(Peer reviewed; Journal article, 2022)In the present investigation, the numerical code WELDSIM is used to simulate butt welding of 4 mm thick plates of S355 steel and AA6082-T6 by Hybrid Metal Extrusion and Bonding (HYB). This is a new solid state joining ... -
Process optimization for the fabrication of an Atomic Layer Deposition reactor for in situ Transmission Electron Microscopy
(Master thesis, 2021)Denne master går gjennom produksjonsprosessen for ein liten ALD reaktor for "in situ" studie i eit TEM mikroskop. Innfallsvinkel er prosessopptamilersing og fabrikkering blir evaluert etter repeterbarhet, kostnad, tid, og ... -
The processing route towards outstanding performance of the severely deformed Al–Mg–Mn-Sc-Zr alloy
(Journal article, 2021)Aiming at obtaining the enhanced mechanical properties profile for lightweight applications, bulk billets of the commercial 1570C aluminium alloy (Al–5Mg-0.18Mn-0.20Sc-0.08Zr, wt. %) with nanosized aluminides of transition ... -
Produced water treatment using hydrocyclones - Theoretical and experimental studies of novel control schemes
(Doctoral theses at NTNU;2022:136, Doctoral thesis, 2022)Produced-water is a non-lucrative by-product of oil and gas production, and the quantity increases as the field ages. Produced-water is either discharged into the sea or reinjected into the field to enhance pressure. As ... -
Producing Floor and Side Panels from Biocomposites
(Doctoral theses at NTNU;2023:81, Doctoral thesis, 2023)High pressure laminates for floor and wall coverings mainly consist of wood fibres and resins. Such laminates are made of a high density fibre board core and several paper sheets glued to the core to obtain a decorative, ... -
Producing Steel Fiber Reinforced Polymer Composite Pipes
(Master thesis, 2016)This study has introduced a novel non-annealed stainless steel fiber with 8 $\mu m$ diameter to make a steel fiber reinforced polymer composite pipe. The primary objective was to make the pipes by the filament winding ... -
Product configurators for engineer-to-order products
(Master thesis, 2020)Produktkonfiguratorer (PCer) er systemer som automatiserer arbeid i salgs- og ingeniørprosesser og gir fordeler som tids- og ressursreduksjoner og kvalitetsforbedringer. Selskaper som produserer Engineer-to-Order (ETO)-produkter ... -
Product configurators for engineer-to-order products
(Master thesis, 2020)Produktkonfiguratorer (PCer) er systemer som automatiserer arbeid i salgs- og ingeniørprosesser og gir fordeler som tids- og ressursreduksjoner og kvalitetsforbedringer. Selskaper som produserer Engineer-to-Order (ETO)-produkter ... -
Product development of a gripping mechanism for a flexible 3D stretch bending machine for industrial applications - Exploring the concepts of set-based concurrent engineering
(Master thesis, 2018)High strength aluminum components are increasingly popular in the automotive industry. Development of novel manufacturing machines for these components is required to gain a competitive edge. An automotive parts manufacturer ... -
Product development of Tribocorrosion laboratory equipment and investigation of CoCrMo alloy integrity as a hip implant in oxygen depleted environments mimicking hypoxia
(Master thesis, 2022)Abstract The final goal of this master thesis is to measure CoCrMo metal behaviour such as electrode potentials and corrosion rates in oxygen-depleted environments while inducing mechanical damage to them. To do this ... -
Product Recovery Options in Closed Loop Supply Chain Networks: A Literature Review
(Chapter, 2023)The growth of the environmental concerns and resource scarcity have motivated organisations to rethink and reconfigure their supply chains. Closed loop supply chains (CLSC) have evolved from being merely a compliance ... -
Production Assurance & Reliability Modelling Tools Comparison - A Case Study on A 4-bed Pressure Swing Adsorption System in Blue Hydrogen Production
(Master thesis, 2023)I denne masteroppgaven er det lagt vekt på produksjonssikkerhet i undervannsproduksjon av blått hydrogen. I fremtiden må energi i stadig større grad komme fra lavkarbonkilder, og blått hydrogen kan bidra til å forme den ... -
Production Assurance and Life Cycle Cost Evaluation of Offshore Development Projects in the Conceptual Design Phase
(Master thesis, 2012)RAM analysis is used to assess system availability in the oil and gas industry. As the concept design for reliability is getting attention throughout various industries, RAM analysis has become a mandatory delivery in the ... -
Production Availability Analysis: Implications on Modelling due to Subsea Conditions
(Master thesis, 2017)Subsea production and processing systems have become a hot topic among research institutes and industries. While highlighting the advantages on production and economy, the reliability issues show a different picture with ... -
Production Control for Operational Excellence: Trenda, Cases and Research Areas
(Chapter, 2012)Industrial companies must strive to achieve operational excellence; and developing and deploying concepts, principle and tools for production control is essential in this. Globalization, sustainability and ICT development ... -
Production Logistics 4.0 - A Conceptual Multiple Case Study Exploring Industry 4.0 in Different Production Environments
(Master thesis, 2016)This project report is the result of a master project conducted within the master s degree program Mechanical Engineering at the Norwegian University of Science and Technology (NTNU). It was conducted as case studies of ... -
Production Planning and Control in Make-to-Order Manufacturing - Selection Criteria
(Master thesis, 2018)Purpose: The purpose of this thesis is to identify appropriate Production Planning and Control (PPC) methods in a Make to Order (MTO) manufacturing environment. This is done through two steps. First, the MTO environment ... -
Production Planning and Control Related Food Waste in Confectionery Supply Chains
(Master thesis, 2019)Food supply chains are complex, with many actors in supply, production, distribution, retail, and consumption all contributing to waste. One example is the confectionery supply chain, which is the focus of this research. ...