Blar i Institutt for materialteknologi på tittel
Viser treff 1897-1916 av 2509
-
Reduction of MnO and SiO2 from Assmang and Comilog based Slags
(Master thesis, 2017)Silicomanganese(SiMn) and ferromanganese (FeMn) represent essential ingredients for the steel producing industries due to enhancing effects on steel quality. While extensive efforts have been made in investigating the ... -
Reduction of Norwegian and Indian ilmenite with carbon monoxide and hydrogen gas blends
(Journal article, 2016)Synthesis gas, produced from natural gas, can be used to minimise coal consumption and carbon dioxide emissions during the processing of ilmenite. Two different ilmenite ores have been reduced with carbon monoxide and ... -
Reduction of Pelletized Tyssedal Ilmenite and the Effect of Changing Gas Composition and Flow, Pellet Size and Pre Oxidation Condition
(Master thesis, 2011)This master thesis is based on reduction experiments of pelletized Tyssedal ilmenite. The focus is set on the effect of changing parameters such as gas composition, gas flow, pellet size and pre-oxidation condition. The ... -
Reduction of SilicoManganese Slags - Comparing Coke and Charcoal as Reductants
(Master thesis, 2023)Produksjonen av silisiummangan (SiMn) er en karbotermisk reduksjonsprosess. Prosessen benytter seg hovedsakelig av det fossile karbonmaterialet koks som reduksjonsmiddel. Økende miljøbekymringer har ført til større intensiver ... -
Reduction of SiO2 to SiC using natural gas
(Journal article; Peer reviewed, 2014)This paper presents a preliminary study of SiC production by use of natural gas for reduction of silica. Direct reduction of SiO2 by gas mixtures containing CH4, H2, and Ar was studied at temperatures between 1273 K and ... -
Reduction Rate of SiMn Slags With Different Carbon Materials
(Master thesis, 2020)I produksjonen av silikomangan (SiMn) er det behov for karbon som reduseringsmiddel, og i dagens industri brukes materialet koks for det meste. Koks har opphav fra fossile kilder, og dersom CO2 utslippet skal reduseres i ... -
Reduction rates of MnO and SiO2 in SiMn slags between 1500 and 1650°C
(Journal article; Peer reviewed, 2019)The kinetics of MnO and SiO2 reduction in SiMn slags based on Assmang/Comilog ore and HCFeMn (high-carbon ferromanganese) slag were investigated between 1500 and 1650°C under a CO atmosphere. The results showed that charges ... -
Reduction Rates of SiMn Slags from Various Raw Materials
(Doctoral theses at NTNU;2018:260, Doctoral thesis, 2018) -
Reduction Rates of SiMn Slags from Various Raw Materials
(Doctoral theses at NTNU;2018:260, Doctoral thesis, 2018)The kinetic information in the SiMn (Silicomanganese) process from melting of raw materials to production of metal was investigated in this work. This is of interest for the SiMn production industries where the effect of ... -
Refining Kinetics of the SisAl Silicon Alloy
(Master thesis, 2023)SisAl Pilot-prosjektet er dedikert til å utforske en mer miljøvennlig tilnærming til produksjon av silisium. Hovedmålet er å redusere karbonavtrykket og energiforbruket forbundet med tradisjonelle metoder ved å erstatte ... -
Refining of Silicon by Solidification of Al-Si Melt
(Master thesis, 2012)Primary silicon crystals grown from an Al-Si melt has been investigated by solidifying directionally and under electromagnetic field. The goal of this thesis was to increase the size of the primary Si crystals and to ... -
Regularized Yield Surfaces for Crystal Plasticity of Metals
(Peer reviewed; Journal article, 2020)The rate-independent Schmid assumption for a metal crystal results in a yield surface that is faceted with sharp corners. Regularized yield surfaces round off the corners and can be convenient in computational implementations. ... -
Relationship between Al-Ni intermetallic Phases and Bond Strength in Roll Bonded Steel-Aluminum Composites with Nickel Interlayers
(Journal article; Peer reviewed, 2019)In this work, the interface characteristics and resulting bond strength were investigated for roll bonded steel-aluminum composites with nickel interlayers, both after rolling and after post-rolling heat treatments at 400 ... -
Remelting of Aluminium by Continuous Submersion of Rolled Scrap
(Dr. ingeniøravhandling, 0809-103X; 2000:127, Doctoral thesis, 2000)When remelting aluminium scrap, metal losses due to dross generation is a common problem. Reduction of these losses will give substantial economic and environmental benefits. Dross is generated when aluminium metal oxidizes ... -
Removal and recovery of indium from ITO coated glass and scraps using molten salt electrolysis
(Peer reviewed; Journal article, 2019)Indium is an important strategic resource due to the scarcity for the metal. In the present study, molten salt electrolysis is used to reduce indium from ITO coated glass and scraps in order to seek a new way to recycle ... -
Removal of Aluminium Carbide from Liquid Aluminium
(Master thesis, 2018)Aluminium carbide (Al4C3) inclusions are a common type of impurity found in aluminium alloys. Currently aluminium carbide cannot be efficiently removed due to its small particle size and wetting properties. The small carbide ... -
Removal of Boron from Silicon by Gas refining with Water and Hydrogen
(Master thesis, 2012)A high demand of silicon for solar cells has lead to a search of an alternative route to solar grade silicon. A suggested method is upgrading metallurgical grade silicon. This thesis focuses on the gas refining of silicon ... -
Removal of boron from silicon by slag treatment and by evaporation of boron from slag in hydrogen atmosphere
(Master thesis, 2012)Background and objective: Removal of boron is one of the main challenges in the purification of metallurgical grade silicon (MG-Si) for solar cells and a simple low cost method is therefore needed. Boron removal by slag ... -
Removal of C and SiC from Si and FeSi during ladle refining and solidification
(Dr.ingeniøravhandling, 0809-103X; 1997:11, Doctoral thesis, 1997) -
Removal of dissolved elementsin aluminium by filtration
(Doktoravhandlinger ved NTNU, 1503-8181; 2009:225, Doctoral thesis, 2009)The objective of this work was to show that removal of alkali from aluminium melts by means of filtration is feasible. Therefore, a chemically active filter based on a packed bed of AlF3 grains was designed and built. ...