Blar i Institutt for maskinteknikk og produksjon på emneord "Produktutvikling og produksjon, Produktutvikling og materialer"
Viser treff 61-80 av 89
-
Optimalisering av translasjonsvibrasjonsdemper for Gopro-kamera
(Master thesis, 2016)Masteroppgaven tar for seg utviklingen av en vibrasjonsdemper for GoPro-kameraer. Leseren tas gjennom hele utviklingsløpet fra idé til ferdig prototype. Løsningen demper rene translasjonsvibrasjoner fra underlaget slik at ... -
Piston Pin Testing
(Master thesis, 2016)This thesis addresses a study undertaken to develop a finite element model and perform quasi-static tests. The test is to simulate the piston and connecting rod execute a pressure force on the piston pin in a Honda CRF250F ... -
Plasticity Effect on Crack Tips with Help of IR-Camera
(Master thesis, 2017)The assessment of the mechanical performance of engineering materials subjected to high cycle fatigue requires very long and costly testing procedures. Therefore, there is a strong drive from industry to find alternative ... -
Prototyping an Experimental Setup for Understanding Affective Response in a Ship Bridge Scenario
(Master thesis, 2016)This document concerns the process and outcome of a master project undertaken at the Department of Engineering Design and Materials (IPM) at the Norwegian University of Science and Technology (NTNU) in the fall of 2015. ... -
Prototyping and Testing During an Assistive Sports Equipment Development Process
(Master thesis, 2018)An important part of the development process is to validate ideas and concepts continuously. Within physical design, this is primarily done by creating prototypes and testing them. This process is especially important ... -
Prototyping and testing of novel flood protection systems
(Master thesis, 2016)This thesis describes the early development stages of novel consumer flood protection systems. The development process has emphasized prototyping and experimentation as a strategy to front-load the development, which is ... -
Rapid prototyping tools
(Master thesis, 2016)This paper is the description of the method and result of the master project of Petter Ildgruben at the Department of Engineering Design and Materials (IPM) at the Norwegian University of Science and Technology (NTNU) in ... -
Residual Strength of Composite Hulls after Impact
(Master thesis, 2016)Norsafe MILPRO boats operates in different waters at high speeds. The chance of hitting unknown objects e.g. floating logs is present. Being able to judge the damages and the residual strengths to these impacts are desirable. ... -
Residual Strength of Composite Pressure Vessels After Impact
(Master thesis, 2016)Composite overwrapped pressure vessels are increasingly being applied for transportation and storage of pressurized fluids. With superior material properties, fiber-reinforced composites are central to increasing operating ... -
Rethinking Surface Design and Materials of Skis
(Master thesis, 2017)Rethinking Surface Design and Materials of Skis -
Separation Plant for Waste Electrical and Electronic Equipment in Bolivia
(Master thesis, 2016)Waste electrical and electronic equipment (WEEE) is becoming an growing problem in developing countries. WEEE often contains hazardous materials as well as expensive and/or rare metals. Treating the waste electronic in ... -
SUBSEA RECEIVER STATION FOR COMMUNICATION WITH DOWN WELL SENSORS - Undervanns mottakerstasjon for kommunikasjon med brønnhull sensorer
(Master thesis, 2013)The scope of this project was to develop a purpose designed communication platform for subsea applications. The company Wireless Instrumentation Systems (WINS) AS has a pilot project with Statoil ASA on the production ... -
The Biocompatibility and Osteogenic Properties of Additive Manufactured Porous Ti-6Al-4V Scaffolds
(Master thesis, 2018)Human bone is constantly being remodeled, and has the ability to repair itself when damage occurs. However, sometimes the fractures are so intense that they exceed the critical non-healable size. In order to repair such ... -
The Effect of Heat-Treatment on Notched Ti-6Al-4V Specimens Produced by Selective Laser Melting Under Fatigue Loading
(Master thesis, 2018)Selective Laser Melting (SLM) is an Additive Manufacturing (AM) technique that can produce metallic parts of arbitrary geometry with densities greater than 99.7%. However, complex shapes lead to notches with different radii ... -
Trailer Suspension Rig for Virtual and Physical Testing
(Master thesis, 2016)The objective of this Master's thesis was to finalize the construction of a physical torsion bar suspension test rig, and perform analytical calculations and virtual simulations related to the rig. This thesis is a ... -
Trajectory Control for Autonomous Working Submersibles
(Master thesis, 2016)This master thesis describes the development of a trajectory control system for autonomous underwater vehicles. The system enables geometric models to follow three dimensional paths, while orientation is controlled by ... -
Use of SED approach to predict the fatigue behaviour of Aluminium V-Notched Samples
(Master thesis, 2018)ABSTRACT 1. COMPUTATION OF STRAIN ENERGY DENSITY FOR V-NOTCHED ALUMINUM SAMPLES 2. DIFFERENCE BETWEEN ELASTIC AND PLASTIC MODEL 3. COMPUTATION OF THE NOTCH STRESS INTENSITY FACTOR 4. DIMENSIONLESS PARAMETER Y 5. INITIATION ... -
User Interface Concepts for Mechanism Modelling in the RaMMS KBE System
(Master thesis, 2017)By combining the principles of knowledge-based engineering (KBE) and concurrent engineering in the design process, repetitive tasks are reduced and design tasks are conducted simultaneously, enabling the engineer to explore ... -
Using Prototypes to Leverage Tacit Knowledge - Experimenting with Tacit Knowledge in Product Development
(Master thesis, 2016)With increasing pressure on knowledge creating companies to innovate faster and better, there is an apparent need for leveraging knowledge transfer both within the organization and within groups of individuals. While the ... -
Utmatting av komposittrør med boltforbindelser
(Master thesis, 2016)Ett system for å koble komposittrør opp mot metallstrukturer har blitt utviklet ved NTNU. Løsningen består av ett metallendestykke med bolter skrudd inn radielt. Egenskapene til et komposittrør koblet opp til to metallendestykker ...