Blar i Fakultet for ingeniørvitenskap (IV) på tittel
Viser treff 17221-17240 av 22924
-
Prototype Experiments: Strategies and Trade-offs
(Journal article; Peer reviewed, 2017)Throughout the whole product development process, there is always a question on whether the proposed product is “up to its task”, and often it is up to the engineer or designer to answer these questions. In many cases, ... -
Prototype Software for Automated Well Planning
(Master thesis, 2019)Kontinuerlig forbedring av utstyr og teknologi har preget petroleumsindustrien opp igjennom årene. Forbedringene i teknologi har muliggjort boring av brønner med stadig økende kompleksitet. Brønnplanleggingsprosessen har ... -
Prototyping a Mechanical Lung for Human Patient Simulators - Concept Development to Facilitate Medical Ventilation Training
(Master thesis, 2019)Denne masteroppgaven tar for seg tidlig-fasen av et utviklingprosjekt for en mekanisk lunge, for en pasient simulator. Prosjektet er utført på TrollLabs på NTNU, og oppgaven er gitt av Laerdal Medical. De had har et behov ... -
Prototyping an Experimental Setup for Understanding Affective Response in a Ship Bridge Scenario
(Master thesis, 2016)This document concerns the process and outcome of a master project undertaken at the Department of Engineering Design and Materials (IPM) at the Norwegian University of Science and Technology (NTNU) in the fall of 2015. ... -
Prototyping an Experimental Setup to Quantify Neurophysiological Response during In Situ Interaction Experiments
(Master thesis, 2020)Denne masteroppgaven beskriver prosessen og resultatene av et masterprosjekt utført ved institutt for maskinteknikk og produksjon (MTP) ved Norges teknisk-naturvitenskapelige universitet (NTNU) i Trondheim våren 2020. Målet ... -
Prototyping and Testing During an Assistive Sports Equipment Development Process
(Master thesis, 2018)An important part of the development process is to validate ideas and concepts continuously. Within physical design, this is primarily done by creating prototypes and testing them. This process is especially important ... -
Prototyping and Testing of a Consumer Grade Flood Protection System
(Master thesis, 2018)Injection moulding is a common production method for mass manufacturing of plastic products. However, creating production-intent prototypes for these products is a challenging task, as injection moulds are expensive to ... -
Prototyping and testing of novel flood protection systems
(Master thesis, 2016)This thesis describes the early development stages of novel consumer flood protection systems. The development process has emphasized prototyping and experimentation as a strategy to front-load the development, which is ... -
Prototyping Cyber-Physical Systems using Wayfaring - An Experiment and Insights for Early-Stage Development
(Doctoral theses at NTNU;2020:389, Doctoral thesis, 2020)The two main aims of the thesis are firstly to qualitatively and quantitatively research the effect of using a prototype-driven wayfaring approach for the early-stage development of cyber-physical systems to give normative ... -
Prototyping in the Industrial Internet
(Master thesis, 2017)Founded on the pre-master project Industrial Internet: Sensor Applications and Measurements in a Workshop Setting (A1) as a starting point for thinking about early stage product development in the industrial internet, ... -
Prototyping installation and commissioning of novel a cleaning robot by using virtual tools – lessons learned
(Journal article; Peer reviewed, 2019)This paper presents a simulation study in which virtual product development tools are used to support the design of a novel robotic cleaning solution for fish processing facilities. The installation and commissioning of ... -
Prototyping of Tangible Programming - An Iterative Approach to a Multidisciplinary Design Problem
(Master thesis, 2015)The Fibo Car is a game interface consisting of a kit of car parts. A virtual model of the assembled parts is generated on a computer and used in a physics engine based gameplay. This product vision is the source of this ... -
Prototyping pharmaceutical containers for rapid dissolution of acetylsalicylic acid for oral administration following a heart attack
(Master thesis, 2019)Denne masteroppgaven beskriver tidligfaseutviklingen av en legemiddelbeholder for rask oppløsning av Acetylsalisylsyre(ASA). ASA er en kjent blodfortynner og er et etablert førstehjelpstiltak når det er mistanke om ... -
Prototyping to Leverage Learning in Product Manufacturing Environments
(Journal article; Peer reviewed, 2016)Rooted in the automotive industry, this article discusses the topic of leveraging tacit knowledge through prototyping. After first providing an overview on learning and knowledge, the Socialization, Externalization, ... -
Provenance of the Neoproterozoic–Cambrian Vestertana Group in Finnmark, northern Norway
(Master thesis, 2023)Detritalzirkonstudier kan bidra til å bestemme paleogeografi, tektoniske rekonstruksjoner og jordskorpeutvikling. Zirkon benyttes populært i sedimentære provenansstudier på grunn av sin robusthet og tilstedeværelse i så ... -
Provincial and sector-level material footprints in China
(Journal article; Peer reviewed, 2019)High-income countries often outsource material demands to poorer countries along with the associated environmental damage. This phenomenon can also occur within (large) countries, such as China, which was responsible for ... -
Provision and Updating of Estimates of Reliability Parameters for Use in Reliability Analyses of Safety-Instrumented Systems
(Master thesis, 2012)Safety-instrumented systems are implemented in the industry to prevent accidents to occur and escalate. The blowdown system on a oil production ship is one example of such system. If a fire breaks out on the ship, the ... -
Provision of Reliability Data for New Technology Equipment in Subsea Production Systems
(Master thesis, 2012)For certain new technologies such as subsea processing systems reliability, compactness and easy maintainability are the most important factors to be considered while designing. This is because installation and retrieval ... -
Provision of Reliability Data for New Technology: Approach for estimation of failure rate function for a sub-sea pump
(Master thesis, 2012)As part of the project thesis the candidate shall work on the following. 1. Document a literature survey of relevant reliability data sources and evaluate these with respect to applicability and quality. The data sources ... -
Proxy Model Development for the Optimization of Water Alternating CO2 Gas for Enhanced Oil Recovery
(Peer reviewed; Journal article, 2023)Optimization studies are an important task in reservoir engineering practices such as production optimization and EOR (Enhanced Oil Recovery) assessments. However, they are extensive studies with many simulations that ...