Blar i Fakultet for ingeniørvitenskap (IV) på tittel
Viser treff 22802-22821 av 23571
-
Validation of Data-Driven Labeling Approaches Using a Novel Deep Network Structure for Remaining Useful Life Predictions
(Journal article; Peer reviewed, 2019)Today, most research studies that aim to predict the remaining useful life (RUL) of industrial components based on deep learning techniques are using piecewise linear (PwL) run-to-failure targets to model the degradation ... -
Validation of decomposition models for solar irradiance at high latitudes: A preliminary study
(Peer reviewed; Journal article, 2023)The accurate estimation of buildings' solar potential contributes to boost the exploitation of solar energy at high latitudes. The decomposition of global irradiation into the direct and diffuse fractions is a fundamental ... -
Validation of dynamic models of the thermal systems of swimming pools
(Master thesis, 2020)Svømmehaller er komplekse bygg som stiller høye krav til både bygningskropp og tekniske systemer. Et velfungerende ventilasjonsaggregat med optimal styring av temperatur- og fuktkontroll er svært viktig for å skape et godt ... -
Validation of Dynamic Risk Analysis Supporting Integrated Operations Across Systems
(Journal article; Peer reviewed, 2019)Dynamic risk analysis (DRA) is a novel industrial approach that aims to capture changes in operational conditions over time and quantify their effect on risk. This aspect may be advantageous for providing insight into the ... -
Validation of Force Propagation Through Composite Suspension Members On A Formula Student Race Car
(Master thesis, 2022)Denne oppgaven prøver å validere kreftene som virker på en Formula Student racerbils hjuloppheng igjennom kvasi-statisk testing. Sammenlikning av opplagerkreftene i to vesentlig forskjellige Abaqus-modeller: én med bestående ... -
Validation of Hydrodynamic Loads on a Large-Diameter Monopile in Regular Waves
(Chapter, 2019)Validated hydrodynamic load models for large-diameter support structures are increasingly important as the industry moves towards larger offshore wind turbines. Experiments at 1:50 scale with stiff, vertical, bottom-fixed, ... -
Validation of hyperspectral camera operations with an experimental aircraft
(Peer reviewed; Journal article, 2022)HYPSO-1 is a Small Satellite with a hyperspectral camera payload inside a six unit cubesat platform, launched january 2022. This paper describes how the operation of the same hyperspectral camera is validated by deployment ... -
Validation of material model for polypropylene (PP)
(Master thesis, 2012)A hyperelastic-viscoplastic material model intended for thermoplastics has been developed by SIMLab at NTNU. This model formed the basis of the thesis, where a material model for the polymer polypropylene was calibrated ... -
Validation of material model for polypropylene (PP)
(Master thesis, 2012)Polymers are the up and coming engineering material. The number of possibleapplications is increasing fast and so is the need for a good polymer material model. Thescientists at SIMLab at NTNU have developed such a material ... -
Validation of multi-body modelling methodology for reconfigurable underwater robots
(Chapter; Peer reviewed, 2016)This paper investigates the problem of employing reconfigurable robots in an underwater setting. The main results presented is the experimental validation of a modelling methodology for a system consisting of N dynamically ... -
VALIDATION OF NON-COMPLIANT PRODUCTS FOR USE WITH SAFETY INSTRUMENTED SYSTEMS
(Master thesis, 2011)This master thesis presents a method that can be used for a third party to validate the SIL for a non-compliant component against the IEC 61508. At first, there is some introduction about the safety instrument system and ... -
Validation of Nonlinear Hydrodynamic Load Models for a Monopile in Long-Crested Waves
(Master thesis, 2018)This Master Thesis studies an offshore wind turbine supported by a monopile structure. Model tests for a fully flexible monopile were carried out in the Ocean Basin facility at SINTEF Ocean in August 2017, through the ... -
Validation of Numerical Models of the Offshore Wind Turbine From the Alpha Ventus Wind Farm Against Full-Scale Measurements Within OC5 Phase III
(Peer reviewed; Journal article, 2020)The main objective of the Offshore Code Comparison Collaboration Continuation, with Correlation (OC5) project is validation of aero-hydro-servo-elastic simulation tools for offshore wind turbines (OWTs) through comparison ... -
Validation of Numerical Models of the Offshore Wind Turbine From the Alpha Ventus Wind Farm Against Full-Scale Measurements Within OC5 Phase III
(Chapter, 2019)The main objective of the Offshore Code Comparison Collaboration Continuation, with Correlation (OC5) project is validation of aero-hydro-servo-elastic simulation tools for offshore wind turbines (OWTs) through comparison ... -
Validation of Numerical Wave Tank Simulations Using REEF3D With JONSWAP Spectra in Intermediate Water Depth
(;Paper No: OMAE2020-18298, V001T01A012, Chapter, 2020)As offshore wind turbines increase in size and output, the support structures are also growing. More sophisticated assessment of the hydrodynamic loads is needed, particularly for the ultimate limit state design. For ... -
Validation of seakeeping calculations of a wind farm installation vessel
(Master thesis, 2016)The title of this master thesis is "Validation of Seakeeping Calculations of a Wind Farm Installation Vessel". The work has been conducted for Fred. Olsen Windcarrier, by Stud. Tech. Sven Ole Mollestad Nicolaysen at the ... -
Validation of ship manoeuvring models using metamodels
(Journal article; Peer reviewed, 2017)This paper describes how simplified auxiliary models—metamodels—can be used to create benchmarks for validating ship manoeuvring simulation models. A metamodel represents ship performance for a limited range of parameters, ... -
Validation of ship manoeuvring simulation models
(Doctoral theses at NTNU;2018:67, Doctoral thesis, 2018)During the last decades the application of ship simulation models for training of pilots, ship design, planning and construction of harbours and waterways, planning of complex marine operations and other engineering purposes ... -
Validation of the average strain energy density criterion for additively manufactured notched polylactide acid specimens
(Peer reviewed; Journal article, 2020)The applicability of the Averaged Strain Energy Density (ASED) criterion [1] to predict the failure of notched Polylactide Acid (PLA) specimens fabricated by Fused Deposition Modeling (FDM) is validated by means of ...