Blar i Fakultet for ingeniørvitenskap (IV) på tittel
Viser treff 17331-17350 av 23204
-
Properties of thermal sprayed coatings for internal use in pipes and bends
(Master thesis, 2015)NTNU/SINTEF are participating in a research project called Smooth Surfaces , financed by Norsk Forskningsråd, and with Brunvoll, Triplex, Omya Hustadmarmor and Aquamarine as industry partners in the project. One of the ... -
Properties of TSA in natural seawater at ambient and elevated temperature
(Journal article; Peer reviewed, 2019)Electrochemical properties of thermal sprayed aluminium (TSA) coating were investigated in natural seawater at elevated temperatures with and without cathodic protection (CP). TSA has a low current density requirement when ... -
Properties of waterproof sprayed concrete tunnel linings: A study of EVA-based sprayed membranes for waterproofing of rail and road tunnels in hard rock and cold climate
(Doctoral thesis at NTNU;2015:197, Doctoral thesis, 2015)Investigate the long term effects of exposure of the SCL lining to higher ground water pressure, particularly the exposure of the membrane to pressurized water at cracks Investigate the effects of slow deformations ... -
Properties, Requirements and Possibilities of Smart Windows for Dynamic Daylight and Solar Energy Control in Buildings: A State-of-the-Art Review
(Journal article; Peer reviewed, 2010)A survey on prototype and currently commercial dynamic tintable smart windows has been carried out. The technologies of electrochromic, gasochromic, liquid crystal and electrophoretic or suspended-particle devices were ... -
Proposal and comparison of an eXogenous Kalman Filter and a Particle Filter for use with ROV thruster models
(Master thesis, 2018)Robust and accurate observer design is a prerequisite for safe and efficient underwater navigation. Especially with today's increased focus on automation and autonomy. In this thesis two model based observer designs for ... -
Proposals for enhancing tactical planning in grocery retailing with S&OP
(Journal article; Peer reviewed, 2018)Purpose The purpose of this paper is to explore tactical planning in grocery retailing and propose how process and integration mechanisms from sales and operations planning (S&OP) can enhance retail tactical ... -
Proposed aspects for evaluation of the value of spaces in historic buildings
(Journal article; Peer reviewed, 2015)There is an unrealised potential for new uses of cultural heritage sites. The purpose of this paper is to identify evaluation aspects for assessing the potential of new uses for cultural heritage places and test the proposed ... -
Proposed framework for flexible de- and remanufacturing systems using cyber-physical systems, additive manufacturing, and digital twins
(Peer reviewed; Journal article, 2022)Under the circular economy paradigm, de- and remanufacturing systems are more relevant than ever. However, such systems present specific challenges related to the system structure, automation, and recovery of complex ... -
Proposed Measures for Cost Reduction in the NTNU Campus Collection Project
(Master thesis, 2022)Denne masteroppgaven er et samarbeid med Statsbygg som omhandler NTNU Campussamlingsprosjektet. Prosjektet styres etter prosjektstrategien Design to Cost (DtC) som har satt en absolutt kostnadsramme på 11.032 milliarder ... -
A proposed simplified technique for confirming high precision GNSS antenna offsets
(Journal article; Peer reviewed, 2010)The purpose of this research was to independently investigate and determine confirmatory calibration procedures for GNSS antennas. This paper focuses on the aspect of simplified techniques for confirming high precision ... -
Proposing a novel approach for testing complex medical task trainer prototypes
(Chapter, 2020)Using the Wayfaring model in the Fuzzy Front End of product development can aid designers in uncovering and answering ambiguous design questions. However, it does not aid the challenge of combining insights and concepts ... -
Propulsion control and thrust allocation on marine vessels
(Doktoravhandlinger ved NTNU, 1503-8181; 2008:203, Doctoral thesis, 2008) -
Propulsion methods for under water snake robots - Investigation and simulation using foil for propulsion of a snake robot
(Master thesis, 2015)In this thesis we present a model of a swimming underwater snake robot. How aquatic animals move in water has fascinated people for decades. NTNU started the research on land based snake robots 11 years ago. The last years ... -
Prosedyre for registrering og rapportering av erfaringstall
(Master thesis, 2019)Formålet med oppgaven er å utarbeide en prosedyre for registrering og rapportering av erfaringstall fra produksjonen. Hensikten med å gjennomføre dette formålet er å øke presisjonen av Veidekkes kostnadsestimater i ... -
Prosedyre for registrering og rapportering av erfaringstall
(Master thesis, 2019)Formålet med oppgaven er å utarbeide en prosedyre for registrering og rapportering av erfaringstall fra produksjonen. Hensikten med å gjennomføre dette formålet er å øke presisjonen av Veidekkes kostnadsestimater i ... -
Prosess og økonomi ved BREEAM-NOR
(Bachelor thesis, 2022)BREEAM er et verdensomspennende miljøsertifiseringssystem for bygg. BREEAM står for Building Research Establishment Environmental Assessment Method. BREEAM-NOR er den norske tilpasningen av BREEAM, utviklet av Grønn ... -
Prosessbeskrivelse av et pukkverk - en kostnads- og optimaliseringsstudie
(Master thesis, 2018)Hva koster det egentlig å produsere et tonn pukk? Dette er viktig informasjon for en pukkprodusent. Ved hjelp av NTNUs kostnadsmodell er selve knusekostnaden for Franzefoss pukkverk i Vassfjell beregnet. For en tretrinnsknust ... -
Prosessbeskrivelse av et pukkverk - en kostnads- og optimaliseringsstudie
(Master thesis, 2018)Hva koster det egentlig å produsere et tonn pukk? Dette er viktig informasjon for en pukkprodusent. Ved hjelp av NTNUs kostnadsmodell er selve knusekostnaden for Franzefoss pukkverk i Vassfjell beregnet. For en tretrinnsknust ... -
Prosessen som verktøy i BIM
(Student paper, others, 2013)Rapporten inneholder to hovedtemaer som dels belyser prosessens betydelse for å skape forståelse for og implementere BIM, og dels undersøker wikien som mulig media for å samle å spre både generell og spesifikk kunnskap om ... -
Prosesser som glemmes eller feilvurderes under reguleringsplanlegging av vegprosjekter i Region midt - Endringer i omfang og kostnader fra reguleringsplan til ferdig bygget veg
(Master thesis, 2018)Hensikten med denne rapporten er å avdekke hvilke prosesser av vegbyggingen som fører til størst kostnadsendring i vegprosjekt. Kostnadssprekker får ofte stor oppmerksomhet, uansett bransje og vegprosjekt er ingen unntak. ...