Browsing Fakultet for ingeniørvitenskap (IV) by Title
Now showing items 17206-17225 of 23204
-
Process simulation of SEWGS technology for applications in the steel industry: Prosess simulering av SEWGS teknologi for bruk i stålindustrien
(Master thesis, 2014)As part of the Dutch national program on CO2 capture (CATO-2), in particular ECN s research within the CEASAR project, this study primarily focuses on capturing CO2 from point sources in the steel industry. Central in this ... -
Process simulation of triethylene glycol based dehydration processes
(Master thesis, 2015)Natural gas contains impurities when produced from a reservoir among these impurities is water. In order to meet downstream transport-, process- and appliance specifications the natural gas need to be dehydrated. One of ... -
A Process-Based Model for Arctic Coastal Erosion Driven by Thermodenudation and Thermoabrasion Combined and including Nearshore Morphodynamics
(Peer reviewed; Journal article, 2022)Various models have recently been developed to describe Arctic coastal erosion. Current process-based models simulate multiple physical processes and combine them interactively to resemble the unique mechanism of Arctic ... -
Processing and indexing of electron backscatter patterns using open-source software
(Peer reviewed; Journal article, 2020)A new method to increase the signal-to-noise ratio S/N of electron backscatter patterns (EBSPs) based upon principal component analysis (PCA) is presented. The PCA denoising method is applied to ten scans of EBSPs from the ... -
Processing of marine controlled-source electromagnetic data
(Doktoravhandlinger ved NTNU, 1503-8181; 2011:68, Doctoral thesis, 2011)The idea to use controlled-source electromagnetics in a marine environment for identification of possible hydrocarbons in the subsurface has been developed during the last decade. This imposes renewed insight and interest ... -
Processing of S-Wave Data in Orthorhombic Media
(Doctoral theses at NTNU;2020:296, Doctoral thesis, 2020) -
The processing route towards outstanding performance of the severely deformed Al–Mg–Mn-Sc-Zr alloy
(Journal article, 2021)Aiming at obtaining the enhanced mechanical properties profile for lightweight applications, bulk billets of the commercial 1570C aluminium alloy (Al–5Mg-0.18Mn-0.20Sc-0.08Zr, wt. %) with nanosized aluminides of transition ... -
Produced water treatment using hydrocyclones - Theoretical and experimental studies of novel control schemes
(Doctoral theses at NTNU;2022:136, Doctoral thesis, 2022)Produced-water is a non-lucrative by-product of oil and gas production, and the quantity increases as the field ages. Produced-water is either discharged into the sea or reinjected into the field to enhance pressure. As ... -
Producing Floor and Side Panels from Biocomposites
(Doctoral theses at NTNU;2023:81, Doctoral thesis, 2023)High pressure laminates for floor and wall coverings mainly consist of wood fibres and resins. Such laminates are made of a high density fibre board core and several paper sheets glued to the core to obtain a decorative, ... -
Producing Gas-Oil Ratio Performance of Conventional and Unconventional Reservoirs
(Master thesis, 2012)This study presents a detailed analysis of producing gas-oil ratio performance characteristics from conventional reservoir to unconventional reservoir. Numerical simulations of various reservoir fluid systems are included ... -
Producing GOR for a Heterogenous-Fluid, Two-Layered Shale Well
(Master thesis, 2019)The thesis takes inspiration from the idea presented by Whitson et al. (2018) to investigate the impact of fluid and rock heterogeneity in a single well drainage volume in an unconventional shale reservoir. Literature study ... -
Producing Steel Fiber Reinforced Polymer Composite Pipes
(Master thesis, 2016)This study has introduced a novel non-annealed stainless steel fiber with 8 $\mu m$ diameter to make a steel fiber reinforced polymer composite pipe. The primary objective was to make the pipes by the filament winding ... -
Product Architecture Compressor Starter.
(Master thesis, 2016)Developing and designing new product architecture for electrical starters. Questing what system can handle high variety both today and tomorrow's variety. Methods found in literature are applied. In this thesis technology ... -
Product configurators for engineer-to-order products
(Master thesis, 2020)Produktkonfiguratorer (PCer) er systemer som automatiserer arbeid i salgs- og ingeniørprosesser og gir fordeler som tids- og ressursreduksjoner og kvalitetsforbedringer. Selskaper som produserer Engineer-to-Order (ETO)-produkter ... -
Product configurators for engineer-to-order products
(Master thesis, 2020)Produktkonfiguratorer (PCer) er systemer som automatiserer arbeid i salgs- og ingeniørprosesser og gir fordeler som tids- og ressursreduksjoner og kvalitetsforbedringer. Selskaper som produserer Engineer-to-Order (ETO)-produkter ... -
Product development of a gripping mechanism for a flexible 3D stretch bending machine for industrial applications - Exploring the concepts of set-based concurrent engineering
(Master thesis, 2018)High strength aluminum components are increasingly popular in the automotive industry. Development of novel manufacturing machines for these components is required to gain a competitive edge. An automotive parts manufacturer ... -
Product development of Tribocorrosion laboratory equipment and investigation of CoCrMo alloy integrity as a hip implant in oxygen depleted environments mimicking hypoxia
(Master thesis, 2022)Abstract The final goal of this master thesis is to measure CoCrMo metal behaviour such as electrode potentials and corrosion rates in oxygen-depleted environments while inducing mechanical damage to them. To do this ... -
Product formation during discharge: a combined modelling and experimental study for Li–O2 cathodes in LiTFSI/DMSO and LiTFSI/TEGDME electrolytes
(Peer reviewed; Journal article, 2021)Li–air or Li–O2 batteries are a promising energy storage technology due to the potentially high energy density. However, significant challenges related to reversible charge/discharge of these cells need to be solved. The ... -
Product formation during discharge: a combined modelling and experimental study for Li–O2 cathodes in LiTFSI/DMSO and LiTFSI/TEGDME electrolytes
(Peer reviewed; Journal article, 2021)Li–air or Li–O2 batteries are a promising energy storage technology due to the potentially high energy density. However, significant challenges related to reversible charge/discharge of these cells need to be solved. The ... -
Product Recovery Options in Closed Loop Supply Chain Networks: A Literature Review
(Chapter, 2023)The growth of the environmental concerns and resource scarcity have motivated organisations to rethink and reconfigure their supply chains. Closed loop supply chains (CLSC) have evolved from being merely a compliance ...