Curing Kinetic and Dynamics of Alkoxysilane Binders
Description
Full text not available
Abstract
Denne oppgaven undersøker herdingen av tre akryl kopolymerbindere (Ac1, Ac2 og Ac3) som in-neholder det reaktive alkoksysilanmonomeren metakryloksypropyltrimetoksysilan, γ-MPS. Alkok-sysilanet gjennomg ̊ar hydrolyse og etterfølgende kondensasjon i nærvær av fuktighet eller flytendevann. Katalysatoren som ble brukt, var dibutyltindiacetat (DBTDA). Reaksjonen ble karakter-isert ved bruk av FT-IR, TGA, DSC og kvalitative m ̊alinger av løselighet og klebrighet. Detre binderne skilte seg b ̊ade i sammensetning og mengde γ-MPS, som ser ut til ̊a være en av deavgjørende egenskapene n ̊ar man forsøker ̊a forutsi tiden som kreves for tilstrekkelig herding. Akryl1 (Ac1), som inneholdt mest γ-MPS, herdet raskest, etterfulgt av akryl 2 (Ac2). Akryl 3 (Ac3),som inneholdt minst γ-MPS, herdet tregest. Relevante IR topper ble identifisert under analysen,inkludert metoksytoppen ved 2841 cm−1, alkoksysilan toppen ved 1083-1088 cm−1, de herdedesiloksan-toppene ved 1064-1066, 1016 og rundt 1000 cm−1, samt en potensiell silanol, eller ødelagtSi-O-bindingstopp ved 910-920 cm−1. I tillegg var det en bred OH-topp i omr ̊adet 3400 cm−1som økte over tid. Høyden p ̊a noen av disse toppene ble sporet som en funksjon av tiden for ̊agi en estimert herdehastighet, selv om det ikke skal tolkes kvantitativt. Under IR analysen bledet oppdaget at tilsetning av flytende vann i bindemidlet før p ̊aføring, til tross for at det er ikkeblandbart, forbedret herdehastigheten betydelig i alle tilfeller. Prøvene der vannet ikke ble tilsatttil slutt herdet i lignende grad, men med betydelig lavere hastighet. Videre ble det oppdaget atselv om lav luftfuktighet (20-30% luftfuktighet) ikke er optimalt for herding, gjelder det sammefor høy luftfuktighet (75%), som indikert av TGA resultatene. Det ser ut til ̊a være et optimaltfuktighetsomr ̊ade et sted i mellom, muligens rundt 40-50% luftfuktighet, der herdingen fortsetter istørst grad. Generelt ble alle binderne nesten fullstendig herdet i løpet av 24 timer, noen raskere,noe som ble observert ved forsvinningen av de alkoksysilan assosierte toppene. Selv n ̊ar reaksjonenble ansett som fullstendig, ser det fremdeles ut til at ikke alle gruppene deltar i kondensasjonen,og silanoler ser ut til ̊a være til stede. Dette indikerer at mens nesten alle metoksygrupper deltari hydrolysen, kondenserer ikke alle. Selv om det ser ut til at noe etterherding finner sted, var en-dringene i spekterene minimale. Det er veldig vanskelig ̊a tolke spekterene med hensyn til spesiellesiloksanstrukturer, da det ogs ̊a er uenighet i litteraturen ang ̊aende tolkningen av fingeravtrykketsregionale topper. TGA analysen er en annen nyttig tilnærming for ̊a karakterisere reaksjonen, dabrøkdelen som motst ̊ar termisk nedbrytning (i denne studien, opptil 800 °C), nesten utelukkende ersiloksannettet. Det er derfor mulig ̊a finne verdien (askeinnholdet) som det spesifikke bindemidletbør nærme seg n ̊ar det herdes optimalt, og deretter vurdere om et bestemt herdingsforsøk harn ̊add denne verdien. Det maksimale askeinnholdet ble m ̊alt til ̊a være 17 vektprosent for Ac1, 14vektprosent for Ac2 og 9 vektprosent for Ac3, alt ved 40% luftfuktighet. Det ser ut til ̊a være enbetydelig avhengighet av askeinnholdet b ̊ade av den relative fuktigheten under herding og mengdentilgjengelig alkoxysilan i ryggraden. Generelt ser det ut til ̊a være mulig ̊a justere tiden som krevesfor optimal herding ved ̊a velge b ̊ade et passende fuktighetsniv ̊a og molfraksjonen av alkoxysilan iryggraden. Det ser ogs ̊a ut til at kondensasjonen ikke fullføres helt med disse binderne, da noensteder forblir hydrolyserte. Det ble vist at silanoler mest sannsynlig er ansvarlige for den bredeOH-toppen. Det er fortsatt vanskelig ̊a tilskrive spesifikke siloksanstrukturer (som burer eller T xnomenklatur) uten ̊a bruke 29Si NMR, da det er uenighet i litteraturen ang ̊aende fingeravtrykkre-gionen i IR-spektrene. Bindemidlets optimale viskositet er ogs ̊a avgjørende for riktig herding, somble bevist ved ̊a justere formuleringen av Ac2, hvor formulasjonen med lavere viskositet (med samemengde alkoksysilan) herdet raskere. This thesis examines the curing behavior of three acrylic co-polymer binders (Ac1, Ac2 andAc3) containing reactive, alkoxysilane monomer, methacryloxypropyl trimethoxysilane, γ-MPS.Alkoxysilanes undergo hydrolysis and subsequent condensation in the presence of ambient mois-ture or liquid water. The catalyst used was dibutyltin diacetate, DBTDA. The reaction wascharacterized by FT-IR, TGA, DSC and qualitative solubility and tackiness measurements. Thethree coatings differed both in composition and the amount of γ-MPS, which appears to be oneof the defining properties, when attempting to predict the time required for a sufficient degree ofcuring. Acrylic 1, containing the most γ-MPS, cured the fastest, followed by Acrylic 2. Acrylic 3,which contained the least, cured the slowest. Relevant IR peaks were identified during the analysis,including the methoxy peak at 2841 cm−1, the alkoxysilane peak at 1083-1088 cm−1, the resultingsiloxane peaks at 1064-1066, 1016 and around 1000 cm−1 and a potential silanol or broken Si – O–bond at 910-920 cm−1, together with an evolving broad -OH peak in the 3400 cm−1 region. Theheight of some of these peaks was tracked as a function of time, to provide an estimation of thecuring rate, though it should not be interpreted quantitatively. During the IR analysis, it wasdiscovered, that addition of liquid water into the binder prior to application, despite being immis-cible, significantly improved the curing rate in all cases. However, the samples where the water wasnot added eventually cured to a similar degree, but at a considerably slower rate. Furthermore,it was discovered, that while low humidity (20-30% RH) is not optimal for the curing, the sameapplies for the high humidity (75% RH), indicated by the TGA results. It appears, that there isan optimal humidity range somewhere in between, possibly around 40-50%RH, where the curingproceeds to the largest extent. In general, all the coatings were almost fully cured in a matter of 24hours, some faster, a fact that was assessed by disappearance of the alkoxysilane associated peaks.Even when the reaction was deemed complete, it still appears that not all the sites partake in con-densation, silanols seem to be present, indicating, that while almost all methoxy groups participatein hydrolysis, not all condense. Even though some post-curing appears to take place, the changesin the spectra were minimal. It is very hard to interpret the spectra with respect to particularsiloxane structures, as there is also a lack of consensus in the literature about the interpretation ofthe fingerprint region peaks. The TGA analysis is another useful approach of characterizing thereaction, as the fraction that resists thermal decomposition (in this study, up to 800 °C) is almostcertainly the siloxane network. Given that, it is possible to find out the value (ash content) thatthe particular binder should approach, when cured optimally and then assess, whether a particularcuring attempt has reached this value. The maximum ash content was measured to be 17 w.t%for Ac1, 14 w.t% for Ac2 and 9 w.t% for Ac3, all at 40% RH. There appears to be a rather strongdependence of the ash content on both the relative humidity during curing and the amount of theavailable alkoxysilane in the backbone.Generally, it appears to be possible to tune the time required for optimal curing by choosing botha suitable humidity level, and the molar fraction of the alkoxysilane in the backbone. It alsoappears that in the case of these binders, the condensation does not proceed fully, with somesites remaining hydrolyzed. It was shown that silanols are most likely responsible for the broadOH peak. It remains difficult to attribute any specific siloxane structures (type of cage, or Txnomenclature) without employing 29Si NMR, as there is a lack of consensus in the literature forthe fingerprint region of the IR spectra. Optimal viscosity of the binder is also crucial for propercuring, as was proved by adjusting the formulation of Acrylic 2, where the formulation with lowerviscosity (containing the same amount of alkoxysilane) has cured faster.