Blar i Øvrige samlinger på tidsskrift "Key Engineering Materials"
Viser treff 1-14 av 14
-
Benefits and Opportunities of Reusing Waste Rotor Blades Materials from a Life Cycle Perspective
(Peer reviewed; Journal article, 2022)The present Life Cycle Analysis (LCA) intends to investigate the environmental benefit of using natural fibres and/or recyclable epoxy resins for future manufacturing of small/medium wind turbine blades to handle thermoset ... -
A comparative study between jute and glass fiber reinforced composites
(Peer reviewed; Journal article, 2021)Recently, natural fiber reinforced polymer composites have become popular over traditional synthetic fiber reinforced polymer composites for automotive, low demanding structural and semi-structural applications. In this ... -
Determination of forming limit strains using Marciniak-Kuczynski tests and automated digital image correlation procedures
(Journal article; Peer reviewed, 2012)Forming limit strains are used to construct a forming limit diagram (FLD), which is a diagram in the principal strain space, traditionally used for designing forming operations of sheet metals. A line indicating the boundary ... -
Effect of Stretching on Springback in Rotary Stretch Bending of Aluminium Alloy Profiles
(Journal article, 2021)Stretch bending is widely used for manufacturing profile-type parts. However, one of the challenges faced by the bending-type forming processes is springback, which significantly reduces the dimensional accuracy of formed ... -
Effect of the fibre type on the rheological and mechanical properties of cementitious composites for thin overlays
(Journal article; Peer reviewed, 2018)Polypropylene (PP), nylon and polyvinyl alcohol (PVA) micro-fibres with different geometries were used at 1 vol. % dosage to investigate rheological and mechanical properties of cementitious composites to be used for thin ... -
Electromagnetic shielding for buildings using hybrid polymer composites: a life cycle assessment study.
(Peer reviewed; Journal article, 2020)In the present paper, we investigated a sandwich composite as a potential electromagnetic interference shielding wall panel for buildings. The panel was built using a ferrite-particle modified high density polyethylene in ... -
In-Process Monitoring of Springback in Industrial Bending Using a Laser Sensor-Based Method
(Peer reviewed; Journal article, 2022)Bent tubes and profiles are widely used in many industries such as automotive, aerospace and shipbuilding. In bending of tubes and profiles, springback is normally regarded as a challenge, affecting the dimensional accuracy ... -
Influence of Annealing of Al-5Ti-1B Master Alloy on Hot Tearing of Cast Al-7Si-3Cu Alloy
(Journal article; Peer reviewed, 2017)Hot tearing is a common and severe defect encountered in aluminium alloys castings. It is affected by alloy composition as well as processing conditions and variables. In Al–7Si-3Cu presence of copper increases mechanical ... -
Influence of Stacking Sequence and Intermediate Layer Thickness in AA6082-IF Steel Tri-Layered Cold Roll Bonded Composite Sheets
(Journal article; Peer reviewed, 2018) -
Insulating and Strength Properties of an Aerogel-Incorporated Mortar Based on UHPC Formulations
(Journal article; Peer reviewed, 2015)With the increasing attention towards energy-efficient and zero emission buildings, improvement to concrete properties is becoming more and more significant in construction and building sectors. One such area is to enhance ... -
Investigation of high-strength steel component subjected to stretch-bending: effect of forming history
(Journal article; Peer reviewed, 2014)The behaviour of a closed top-hat section made of Dogal 800 DP subjected to stretch-bending is studied both experimentally and numerically. The top-hat section was made by forming of a sheet using a FlexformTM fluid cell ... -
Macroscopic modelling of Flow-Drill Screw connections
(Journal article; Peer reviewed, 2016)This study focuses on the modelling of Flow-Drill Screw (FDS) connections in large-scale shell analyses. Macroscopic connection models for large-scale crash simulations were assessed for modelling of FDS connections between ... -
On the use of carbon nanotubes to develop durable structural electrodes for self-sensing applications
(Peer reviewed; Journal article, 2020)This paper reports an experimental investigation on embedded polyurethane (PUR) electrodes into a carbon fibre reinforced polymer (CFRP) composite to enable the dependable use of composites as a piezoresistive sensors, ... -
Sustainable reinforced concrete design of structural walls
(Peer reviewed; Journal article, 2021)Sustainability calls for reduction in the use of natural resources and man-made materials. In light of this, the present study demonstrates the potentials of the reduction of transverse reinforcement in structural walls. ...