Blar i Fakultet for naturvitenskap (NV) på tidsskrift "Materials Science & Engineering: A"
Viser treff 1-20 av 32
-
Achieving high-strength metallurgical bonding between A356 aluminum and copper through compound casting
(Peer reviewed; Journal article, 2021)Due to stable surface oxides on the solid copper surface and the ease of forming Al2O3 films at the aluminum melt surface, it is difficult to achieve high-strength metallurgical bonding between the two materials through ... -
Deformation behavior, microstructure evolution, and dynamic recrystallization mechanism of an AZ31 Mg alloy under high-throughput gradient thermal compression
(Peer reviewed; Journal article, 2022)A high-throughput gradient thermal compression process was adopted to investigate the effects of thermal deformation parameters on the deformation behavior and microstructure evolution of a rolled AZ31 Mg alloy. The results ... -
Deformation of an Al-7Mg alloy with extensive structural micro-segregations during dynamic plastic deformation
(Journal article; Peer reviewed, 2015)The microstructure evolution and deformation behavior of an as-cast Al–7Mg alloy with severe Mg segregation zones distributed on grain boundaries and in interdendrite regions subjected to dynamic plastic deformation (DPD) ... -
Effect of cyclic ageing on the early-stage clustering in Al–Zn-Mg(-Cu) alloys
(Peer reviewed; Journal article, 2022)The cyclic application of mechanical stress to aluminum alloys at room temperature, referred to as cyclic ageing, continuously injects vacancies, enabling dynamic precipitation of a fine distribution of solute clusters. ... -
Effect of heat input on nanomechanical properties of wire-arc additive manufactured Al 4047 alloys
(Peer reviewed; Journal article, 2022)Heat input is one of the most important process parameters during additive manufacturing (AM). It is of great significance to understand the effect of heat input on the microstructure and nanomechanical properties, as well ... -
Effect of pre-deformation on age-hardening behaviors in an Al-Mg-Cu alloy
(Peer reviewed; Journal article, 2021)The effects of 3%–50% pre-deformation following solution heat treatment on the age hardening of an Al-3Mg-1Cu alloy have been investigated by Vickers microhardness measurement, tensile tests, differential scanning calorimetry, ... -
Effects of cryogenic temperature and pre-stretching on mechanical properties and deformation characteristics of a peak-aged AA6082 extrusion
(Journal article; Peer reviewed, 2017)Plastic deformation studies of a peak-aged AA6082 alloy by means of tensile tests at 77 K and 295 K, and related microstructure characteristics obtained by Scanning Electron Microscopy (SEM), Electron Backscatter Diffraction ... -
Enhanced ductility and strength in a cast Al–Mg alloy with high Mg content
(Journal article; Peer reviewed, 2021)Cast Al–Mg alloys with high Mg content have attracted considerable interest as a result of exceptionally low mass density and enhanced Mg solid-solution strengthening effect. However, poor ductility in this class of cast ... -
Enhanced nucleation and precipitation hardening in Al-Mg-Si(-Cu) alloys with minor Cd additions
(Peer reviewed; Journal article, 2020)This work reports a novel effect of impurity element Cd on enhancing the precipitation kinetics and increasing the peak hardness of Al–Mg–Si(–Cu) alloys during artificial ageing. It is found that the number density of age ... -
Evolution in microstructure and properties during non-isothermal annealing of a cold-rolled Al-Mn-Fe-Si alloy with different microchemistry states
(Journal article, 2015)The softening behaviour during non-isothermal annealing of a cold-rolled Al–Mn–Fe–Si model alloy was studied as a function of the state of microchemistry, in terms of the solute level of Mn, size and spatial distribution ... -
How calcium prevents precipitation hardening in Al–Mg–Si alloys
(Journal article, 2013)We have investigated the effect on precipitate microstructure and hardness upon adding small amounts of Ca to a base Al–Mg–Si alloy. The main investigative techniques were transmission and scanning electron microscopy. We ... -
An improved modelling framework for strength and work hardening of precipitate strengthened Al–Mg–Si alloys
(Journal article; Peer reviewed, 2022)A modelling framework for the strength and work hardening contributions in age hardened Al–Mg–Si alloys is presented. The modelling work is based on transmission electron microscopy (TEM) measurements of the needle-shaped ... -
Interface Microstructure and Tensile Properties of a Third Generation Aluminium-Steel Butt Weld Produced Using the Hybrid Metal Extrusion & Bonding (HYB) Process
(Peer reviewed; Journal article, 2021)The Hybrid Metal Extrusion & Bonding (HYB) process is a patented solid state joining method for metals which utilizes filler material additions to consolidate the weld. In the present investigation the interface microstructure ... -
Linking mechanical properties to precipitate microstructure in three Al-Mg-Si(-Cu) alloys
(Peer reviewed; Journal article, 2021)The mechanical properties of age hardenable Al alloys depend strongly on the precipitate microstructure. This work has investigated the relationship between properties such as strength and ductility and the distribution ... -
Local mechanical properties and precipitation inhomogeneity in large-grained Al–Mg–Si alloy
(Peer reviewed; Journal article, 2022)Al–Mg–Si (6xxx series) alloys show excellent mechanical properties due to the precipitates formed during heat treatment. However, heat treatment of these alloys results in a soft precipitation free zone (PFZ) close to grain ... -
Microstructure and enhanced mechanical properties of an Mg-10Gd-2Y-0.5Zr alloy processed by cyclic extrusion and compression
(Journal article; Peer reviewed, 2011)The evolution of microstructure and texture of an extruded GW102K Mg alloy processed by cyclic extrusion and compression (CEC) at 450 °C were investigated. Tensile tests were performed at room temperature and strain rate ... -
Microstructure and mechanical properties of Al-xMg alloys processed by room temperature ECAP
(Journal article; Peer reviewed, 2012)Microstructure development and mechanical properties of Al–xMg alloys (x = 0, 1, 5–10 wt%), processed by ECAP at room temperature, have been investigated. The results show that the microstructures of Al–xMg alloys are ... -
Microstructure and mechanical properties of the AZ31/GW103K bimetal composite rods fabricated by co-extrusion
(Peer reviewed; Journal article, 2022)The AZ31/GW103K bimetal composite rods consisting of a soft AZ31 sleeve and a hard GW103K core were fabricated by the co-extrusion at 350 °C, 400 °C and 450 °C, and their microstructure and mechanical properties were ... -
Microstructure evolution of commercial pure titanium during equal channel angular pressing
(Journal article; Peer reviewed, 2010)The microstructure development of commercially pure titanium during 3 and 4 passes of equal channel angular pressing (ECAP) has been investigated in detail by optical microscopy and electron backscattered diffraction (EBSD). ... -
Precipitation behavior in an Al-Cu-Mg-Si alloy during ageing
(Peer reviewed; Journal article, 2019)The precipitation behavior and aging response of an Al-4.9Cu-0.74Mg-0.51Si-0.48Mn-0.1Cr-0.08Ti-0.02Fe (wt. %) alloy was examined in detail after aging at 170 °C with different dwell times up to 96 h. Deformation by ...