Vis enkel innførsel

dc.contributor.authorHu, Kai
dc.contributor.authorTang, Kai
dc.contributor.authorLv, Xuewei
dc.contributor.authorSafarian, Jafar
dc.contributor.authorYan, Zhiming
dc.contributor.authorSong, Bing
dc.date.accessioned2021-02-19T12:45:29Z
dc.date.available2021-02-19T12:45:29Z
dc.date.created2020-11-10T18:46:54Z
dc.date.issued2020
dc.identifier.citationMetallurgical and Materials Transactions B. 2020, 52B 245-254.en_US
dc.identifier.issn1073-5615
dc.identifier.urihttps://hdl.handle.net/11250/2729261
dc.description.abstractTiO2-FeO-Ti2O3 slag system is the dominant system for industrial high-titania slag production. In the present work, viscosities of TiO2-FeO and TiO2-FeO-Ti2O3 systems were experimentally determined using the concentric rotating cylinder method under argon atmosphere. A viscosity model suitable for the TiO2-FeO-Ti2O3 slag system was then established based on the modification of the Vogel-Fulcher-Tammann (VFT) equation. The experimental results indicate that completely melted high-titania slags exhibit very low viscosity of around 0.8 dPa s with negligible dependence on temperature and compositions. However, it increases dramatically with decreasing temperature slightly below the critical temperature. Besides, the increase in FeO content was found to remarkably lower the critical temperature, while the addition of Ti2O3 increases it. The developed model can predict the viscosities of the TiO2-FeO-Ti2O3 and TiO2-FeO systems over wide ranges of compositions and temperatures within experimental uncertainties. The average relative error for the present model calculation is < 18.82 pct, which is better than the previously developed models for silicate slags reported in the literature. An iso-viscosity distribution diagram was made for the TiO2-FeO-Ti2O3 slag system, which can serve as a roadmap for the Ilmenite smelting reduction process as well as the high titania slags tapping process.en_US
dc.language.isoengen_US
dc.publisherSpringeren_US
dc.rightsNavngivelse 4.0 Internasjonal*
dc.rights.urihttp://creativecommons.org/licenses/by/4.0/deed.no*
dc.titleModeling Viscosity of High Titania Slagen_US
dc.typePeer revieweden_US
dc.typeJournal articleen_US
dc.description.versionpublishedVersionen_US
dc.source.pagenumber245-254en_US
dc.source.volume52Ben_US
dc.source.journalMetallurgical and Materials Transactions Ben_US
dc.identifier.doi10.1007/s11663-020-02002-8
dc.identifier.cristin1846698
dc.description.localcodeThis article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativec ommons.org/licenses/by/4.0/.en_US
cristin.ispublishedtrue
cristin.fulltextoriginal
cristin.qualitycode2


Tilhørende fil(er)

Thumbnail

Denne innførselen finnes i følgende samling(er)

Vis enkel innførsel

Navngivelse 4.0 Internasjonal
Med mindre annet er angitt, så er denne innførselen lisensiert som Navngivelse 4.0 Internasjonal