Vis enkel innførsel

dc.contributor.authorKantar, Emre
dc.contributor.authorHvidsten, Sverre
dc.contributor.authorMauseth, Frank
dc.contributor.authorIldstad, Erling
dc.date.accessioned2019-02-25T08:21:45Z
dc.date.available2019-02-25T08:21:45Z
dc.date.created2018-07-06T12:01:59Z
dc.date.issued2018
dc.identifier.citationTribology International. 2018, 127 361-371.nb_NO
dc.identifier.issn0301-679X
dc.identifier.urihttp://hdl.handle.net/11250/2587118
dc.description.abstractMorphology of the contact area between solid insulation materials ultimately determines the short- and long-term electrical properties of the complete insulation system. The main purpose of this paper is to propose a statistical model to examine the real area of contact between solid dielectric surfaces and secondly to verify and correlate the model outputs with experiments. The model computes the real area of contact, number of contact spots and average cavity size at the interface as a function of elasticity, contact force, and surface roughness. Then, using the average cavity size and the Paschen's law, the discharge inception field of the cavity (CDIE) is estimated. AC breakdown strength (BDS) testing of solid-solid interfaces was carried out, where cross-linked polyethylene (XLPE) samples with four different surface roughnesses were tested at various contact pressures. Following the increased contact force, the calculated average cavity size decreased by a factor of 4.08-4.82 from the roughest to the smoothest surface, corresponding to increased CDIEs by a factor of 2.01-2.56. Likewise, the experimentally obtained BDS values augmented by a factor of 1.4-1.7 when the contact pressure was elevated from 0.5 MPa to 1.16 MPa. A linear correlation between the CDIE and BDS was assumed, yielding a correlation coefficient varying within 0.8-1.3. When the 90% confidence intervals were considered, the range reduced to 0.86-1.05. This correlation suggests that interfacial breakdown phenomenon is strongly related to the interfacial cavity discharge. Hence, the proposed model is verified with experiments.nb_NO
dc.language.isoengnb_NO
dc.publisherElseviernb_NO
dc.relation.urihttps://www.sciencedirect.com/science/article/pii/S0301679X18301403
dc.rightsAttribution-NonCommercial-NoDerivatives 4.0 Internasjonal*
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/4.0/deed.no*
dc.titleA stochastic model for contact surfaces at polymer interfaces subjected to an electrical fieldnb_NO
dc.typeJournal articlenb_NO
dc.typePeer reviewednb_NO
dc.description.versionacceptedVersionnb_NO
dc.source.pagenumber361-371nb_NO
dc.source.volume127nb_NO
dc.source.journalTribology Internationalnb_NO
dc.identifier.doi10.1016/j.triboint.2018.03.003
dc.identifier.cristin1596098
dc.relation.projectNorges forskningsråd: 228344/E30nb_NO
dc.description.localcode© 2018. This is the authors’ accepted and refereed manuscript to the article. Locked until 16.3.2020 due to copyright restrictions. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/nb_NO
cristin.unitcode194,63,20,0
cristin.unitnameInstitutt for elkraftteknikk
cristin.ispublishedtrue
cristin.fulltextpreprint
cristin.qualitycode2


Tilhørende fil(er)

Thumbnail

Denne innførselen finnes i følgende samling(er)

Vis enkel innførsel

Attribution-NonCommercial-NoDerivatives 4.0 Internasjonal
Med mindre annet er angitt, så er denne innførselen lisensiert som Attribution-NonCommercial-NoDerivatives 4.0 Internasjonal