Vis enkel innførsel

dc.contributor.authorAune, Vegard
dc.contributor.authorFagerholt, Egil
dc.contributor.authorHauge, Kristoffer Olsen
dc.contributor.authorLangseth, Magnus
dc.contributor.authorBørvik, Tore
dc.date.accessioned2017-10-02T11:51:10Z
dc.date.available2017-10-02T11:51:10Z
dc.date.created2016-03-30T12:29:00Z
dc.date.issued2016
dc.identifier.citationInternational Journal of Impact Engineering. 2016, 90 106-121.nb_NO
dc.identifier.issn0734-743X
dc.identifier.urihttp://hdl.handle.net/11250/2457721
dc.description.abstractThis work presents results from an experimental investigation on the influence of stand-off distance on the dynamic response of thin ductile plates subjected to airblast loading. The square plates had an exposed area of 0.3×0.3m2 and were manufactured from two different materials, i.e., medium-strength steel and low-strength aluminium. The airblast loading was generated by detonating spherical charges of plastic explosive at various stand-off distances relative to the centre of the plates. Piezoelectric pressure sensors were used for pressure recordings, and synchronized with two high-speed cameras in a stereoscopic setup to capture the response of the targets. The 0.8 mm thick plates were painted with a speckle pattern to measure the transient deformation fields using a three-dimensional digital image correlation (3D-DIC) technique. The tests covered the entire range of structural response from complete failure at the support to a more counter-intuitive behaviour where the permanent mid-point deflection was in the opposite direction to the incident blast wave due to reversed snap buckling. The synchronization of the pressure and displacement measurements enabled a thorough examination of the entire experiment. The trend in all tests was that the maximum response is driven by the positive impulse from the airblast, as it occurred after the positive duration of the pressure pulse. However, depending on the intensity of the blast load and the structural characteristics, elastic effects and the negative phase could play an important role in the final configuration of the plate. Comparison of the permanent deflection and the measurements from digital image correlation confirmed that this technique is capable of accurately measuring the structural response at high loading rates.nb_NO
dc.language.isoengnb_NO
dc.publisherElseviernb_NO
dc.rightsAttribution-NonCommercial-NoDerivatives 4.0 Internasjonal*
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/4.0/deed.no*
dc.titleExperimental study on the response of thin aluminium and steel plates subjected to airblast loadingnb_NO
dc.typeJournal articlenb_NO
dc.typePeer reviewednb_NO
dc.description.versionacceptedVersionnb_NO
dc.source.pagenumber106-121nb_NO
dc.source.volume90nb_NO
dc.source.journalInternational Journal of Impact Engineeringnb_NO
dc.identifier.doi10.1016/j.ijimpeng.2015.11.017
dc.identifier.cristin1347589
dc.relation.projectNorges forskningsråd: 237885nb_NO
dc.description.localcode© 2015. This is the authors’ accepted and refereed manuscript to the article. This manuscript version is made available under the CC-BY-NC-ND 4.0 license http://creativecommons.org/licenses/by-nc-nd/4.0/ LOCKED until 24.12.2017 due to copyright restrictions.nb_NO
cristin.unitcode194,64,45,0
cristin.unitnameInstitutt for konstruksjonsteknikk
cristin.ispublishedtrue
cristin.fulltextpostprint
cristin.qualitycode1


Tilhørende fil(er)

Thumbnail

Denne innførselen finnes i følgende samling(er)

Vis enkel innførsel

Attribution-NonCommercial-NoDerivatives 4.0 Internasjonal
Med mindre annet er angitt, så er denne innførselen lisensiert som Attribution-NonCommercial-NoDerivatives 4.0 Internasjonal