Blar i Institutt for vareproduksjon og byggteknikk på tittel
Viser treff 259-278 av 1005
-
Effect of an Electric Vehicle Promotion Policy on China's Islands: A Case Study of Hainan Island
(Journal article; Peer reviewed, 2020) -
Effect of Si content on the microstructure and properties of Al–Si alloys fabricated using hot extrusion
(Journal article; Peer reviewed, 2017)Al–(12, 20, 35 wt%)Si alloys were fabricated using powder metallurgy process involving hot pressing followed by hot extrusion. The effect of Si content on the microstructure [by scanning electron microscopy], the mechanical ... -
Effect of stacking sequence on the performance of hybrid natural/synthetic fiber reinforced polymer composite laminates
(Peer reviewed; Journal article, 2021)Here, the effect of stacking sequence on the mechanical and thermomechanical properties of composites using natural fiber (jute), synthetic fiber (glass) and unsaturated polyester resin, is presented. The fabricated composite ... -
Effect of time dependent corrosion rate on residual capacity of corroded RC beam
(Journal article; Peer reviewed, 2019)Corrosion is the most commonly severe defect in reinforced concrete (RC) structures and it mainly causes reduced rebar cross-section. The corrosion rate is the determining parameter of the progress of corrosion-induced ... -
Effect of Weather Condition on LoRa IoT Communication Technology in a Tropical Region: Malaysia
(Peer reviewed; Journal article, 2021)An experimental study on the effect of weather conditions such as solar radiation, humidity, temperature, and rain on the Long Range (LoRa) communication in a tropical region (Malaysia) via a campus environment has been ... -
Effective Rate Evaluation of RIS-Assisted Communications Using the Sums of Cascaded α-μ Random Variates
(Peer reviewed; Journal article, 2021)This paper begins with the characterization of the sum of M versions of cascaded α-μ (equivalently, N*(α-μ)) distributed random variates (RVs), and later on, explores the feasibility and applicability of the obtained results ... -
Effective Rate Evaluation with Assistance of Mixture Gamma (MG), Mixture of Gaussian (MoG), and Fox's H-Function Distributions
(Chapter, 2021)This paper investigates the effective rate when the instantaneous received signal-to-noise ratio (SNR) could be modeled as the mixture Gamma (MG), mixture of Gaussian (MoG), and Fox’s H-function distributed random variable ... -
Effective Throughput Analysis of α-η-κ-µ Fading Channels
(Peer reviewed; Journal article, 2020)The α-η-κ-μ fading model is a very useful instrument to accurately describe various radio wave propagation scenarios. In this paper, we study the effective throughput performance of communication systems over the α-η-κ-μ ... -
Effects of accelerated aging on the appearance and mechanical performance of materials jetting products
(Peer reviewed; Journal article, 2023)As a result of the associated costs and environmental impacts, Material Jetting (MJT) plays a limited role in Additive Manufacturing (AM). Research on the durability and long-term performance of MJT objects by evaluating ... -
Effects of Seasonal Temperature Variation on Slurry Temperature and Biogas Composition of a Commercial Fixed-Dome Anaerobic Digester Used in Bangladesh
(Peer reviewed; Journal article, 2021)Biogas is produced in Bangladesh mostly through fixed-dome anaerobic digesters, which usually operate without any temperature controller. An experiment was conducted to monitor the seasonal temperature variation inside a ... -
Effektivisering av dekkeløsning i O2-bygget
(Bachelor thesis, 2020)Dette arbeidet fokuserer på å beregne en alternativ dekkeløsning for O2-bygget i Steinkjer. Bygget er under bygging og hensikten med arbeidet er dermed ikke å påvirke byggeprosessen. I bygget benyttes det krysslimt ... -
Effektivisering av laserskann til BIM
(Bachelor thesis, 2019)Oppgavens hensikt var å finne den mest effektive metoden for å modellere et eksisterende bygg til BIM og hvilke konsekvenser effektiviseringen har. Oppgaven baserte seg på to forskjellige laserskann av samme bygning. På ... -
Effektivitet i driftskontrakter
(Bachelor thesis, 2020)Hensikten med denne bacheloroppgaven er å undersøke hvordan omstruktureringen av vegadministrasjonen påvirker effektivitet i driftskontrakter. Studien er gjennomført på oppdrag fra Statens vegvesen, og formålet med oppgaven ... -
Effektivitetsstudie av fotogrammetrisk kartlegging med droner
(Bachelor thesis, 2019)Hovedmålet i oppgaven er «Hva er effektivitets forskjell mellom en amatørdrone (Dji) og en profesjonell drone (Wingtra)?» Oppgaven er gjennomført som en casestudie. Oppgaven tar for seg dronene i sin helhet og viser en ... -
Eierstyring ved hjelp av ISO 19650
(Bachelor thesis, 2020)Bakgrunn for oppgaven er analyse av den nye ISO standarden, NS-EN ISO 19650-1&2:2018 (Organisering og digitalisering av informasjon om byggverk, inkludert bygningsinformasjonsmodellering (BIM), Informasjonsforvaltning med ... -
Electrical consumption dilemma - All we need is a new metering system?
(Master thesis, 2016-09-29)Electricity consumption are increasing, as our society keeps on growing. Due to climate changes and human impacts, it is clearly that we need to slow down this trend. One of the most important activity that each consumer ... -
Electromagnetic shielding for buildings using hybrid polymer composites: a life cycle assessment study.
(Peer reviewed; Journal article, 2020)In the present paper, we investigated a sandwich composite as a potential electromagnetic interference shielding wall panel for buildings. The panel was built using a ferrite-particle modified high density polyethylene in ... -
Elektrisitetsproduksjon med ORC-teknologi ved fjernvarmedrift
(Bachelor thesis, 2023)Denne bacheloroppgaven undersøker bruk av ORC-teknologi som et bærekraftig og økonomisk bidrag for energiproduksjon, i lys av økte strømpriser og energiknapphet. Arbeidet er motivert av Eidsiva Bioenergi AS sitt vellykkede ... -
Element CC 600
(Bachelor thesis, 2023)I denne bacheloroppgaven er det undersøkt byggetekniske prinsipper for å gi konkrete anbefalinger til hvordan Element CC600 kan anvendes i tak-, yttervegg-, etasjeskiller-, og gulvkonstruksjoner, i en bærende konstruksjon ... -
Emballering hos Plastal AS
(Bachelor thesis, 2009)Dette er rapporten til et hovedprosjekt ved Høgskolen i Gjøvik der 3 elever har kjørt et forbedringsprosjekt for Plastal Raufoss AS. Plastal AS produserer i dag støtfangere for bilgiganten Volvo. Utgangspunktet og ...